Cisco 10BASE-FL Installation And Configuration Manual

Download Installation and configuration manual of Cisco 10BASE-FL Adapter for Free or View it Online on All-Guides.com.

Brand: Cisco

Category: Adapter

Type: Installation and configuration manual

Model: Cisco 10BASE-FL , Cisco PA-5EFL=

Pages: 40 (0.98 Mb)

Download Cisco 10BASE-FL Installation and configuration manual

Cisco 10BASE-FL Installation and configuration manual - Page 1
1
Cisco 10BASE-FL Installation and configuration manual - Page 2
2
Cisco 10BASE-FL Installation and configuration manual - Page 3
3
Cisco 10BASE-FL Installation and configuration manual - Page 4
4
Cisco 10BASE-FL Installation and configuration manual - Page 5
5
Cisco 10BASE-FL Installation and configuration manual - Page 6
6
Cisco 10BASE-FL Installation and configuration manual - Page 7
7
Cisco 10BASE-FL Installation and configuration manual - Page 8
8
Cisco 10BASE-FL Installation and configuration manual - Page 9
9
Cisco 10BASE-FL Installation and configuration manual - Page 10
10
Cisco 10BASE-FL Installation and configuration manual - Page 11
11
Cisco 10BASE-FL Installation and configuration manual - Page 12
12
Cisco 10BASE-FL Installation and configuration manual - Page 13
13
Cisco 10BASE-FL Installation and configuration manual - Page 14
14
Cisco 10BASE-FL Installation and configuration manual - Page 15
15
Cisco 10BASE-FL Installation and configuration manual - Page 16
16
Cisco 10BASE-FL Installation and configuration manual - Page 17
17
Cisco 10BASE-FL Installation and configuration manual - Page 18
18
Cisco 10BASE-FL Installation and configuration manual - Page 19
19
Cisco 10BASE-FL Installation and configuration manual - Page 20
20
Cisco 10BASE-FL Installation and configuration manual - Page 21
21
Cisco 10BASE-FL Installation and configuration manual - Page 22
22
Cisco 10BASE-FL Installation and configuration manual - Page 23
23
Cisco 10BASE-FL Installation and configuration manual - Page 24
24
Cisco 10BASE-FL Installation and configuration manual - Page 25
25
Cisco 10BASE-FL Installation and configuration manual - Page 26
26
Cisco 10BASE-FL Installation and configuration manual - Page 27
27
Cisco 10BASE-FL Installation and configuration manual - Page 28
28
Cisco 10BASE-FL Installation and configuration manual - Page 29
29
Cisco 10BASE-FL Installation and configuration manual - Page 30
30
Cisco 10BASE-FL Installation and configuration manual - Page 31
31
Cisco 10BASE-FL Installation and configuration manual - Page 32
32
Cisco 10BASE-FL Installation and configuration manual - Page 33
33
Cisco 10BASE-FL Installation and configuration manual - Page 34
34
Cisco 10BASE-FL Installation and configuration manual - Page 35
35
Cisco 10BASE-FL Installation and configuration manual - Page 36
36
Cisco 10BASE-FL Installation and configuration manual - Page 37
37
Cisco 10BASE-FL Installation and configuration manual - Page 38
38
Cisco 10BASE-FL Installation and configuration manual - Page 39
39
Cisco 10BASE-FL Installation and configuration manual - Page 40
40
24 PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration
VIP2 and the 5EFL Port Adapter
To determine which type of port adapter is installed on a VIP2 in your system, use the show diag slot
command. Specific port adapter information is displayed, as shown in the following example of a
5EFL port adapter in chassis slot 1:
Router# show diag 1
Slot 1:
Physical slot 1, ~physical slot 0xE, logical slot 1, CBus 0
Microcode Status 0xC
Master Enable, LED, WCS Loaded
Board is analyzed
Pending I/O Status: Console I/O
EEPROM format version 1
VIP2 controller, HW rev 2.2, board revision UNKNOWN
Serial number: 03508056 Part number: 73-1554-02
Test history: 0x00 RMA number: 43-27-00
Flags: cisco 7000 board; 7500 compatible
EEPROM contents (hex):
0x20: 01 15 02 02 00 35 87 58 49 06 12 02 00 2B 1B 00
0x30: 12 2B 00 2A 1A 00 00 00 00 00 00 00 00 00 00 00
Slot database information:
Flags: 0x4 Insertion time: 0x10DC (00:01:17 ago)
Controller Memory Size: 8 MBytes
PA Bay 1 Information:
Ethernet PA, 5 ports
EEPROM format version 1
HW rev 1.0, Board revision 6
Serial number: 03522225 Part number: 73-1679-01
Using the ping Command
The packet internet groper (ping) command allows you to verify that an interface port is functioning
properly and to check the path between a specific port and connected devices at various locations on
the network. This section provides brief descriptions of the ping command. After you verify that the
system and VIP2 have booted successfully and are operational, you can use this command to verify
the status of interface ports. Refer to the publications listed in the section “If You Need More
Information” on page 2, for detailed command descriptions and examples.
The ping command sends an echo request out to a remote device at an IP address that you specify.
After sending a series of signals, the command waits a specified time for the remote device to echo
the signals. Each returned signal is displayed as an exclamation point (!) on the console terminal;
each signal that is not returned before the specified time-out is displayed as a period (.). A series of
exclamation points (!!!!!) indicates a good connection; a series of periods (.....) or the messages
[timed out] or [failed] indicate that the connection failed.
Following is an example of a successful ping command to a remote server with the address 1.1.1.10:
Router# ping 1.1.1.10 <Return>
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echoes to 1.1.1.10, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms
Router#
If the connection fails, verify that you have the correct IP address for the server and
that the server is active (powered on), and repeat the ping command.
For complete descriptions of interface subcommands and the configuration options available for
VIP2-related interfaces, and which support VIP2 functionality, refer to the publications listed in the
section “If You Need More Information” on page 2.