CTEK XS 0.8 Troubleshooting Manual

Download Troubleshooting manual of CTEK D250S Dual Automobile Accessories, Automobile Battery Charger for Free or View it Online on All-Guides.com. This version of CTEK D250S Dual Manual compatible with such list of devices, as: MULTI XS 3600, MXS 10, MXS 25, MXS 5.0, MXS 5.0 Polar

CTEK D250S Dual Troubleshooting manual - Page 1
1
CTEK D250S Dual Troubleshooting manual - Page 2
2
CTEK D250S Dual Troubleshooting manual - Page 3
3
CTEK D250S Dual Troubleshooting manual - Page 4
4
CTEK D250S Dual Troubleshooting manual - Page 5
5
CTEK D250S Dual Troubleshooting manual - Page 6
6
CTEK D250S Dual Troubleshooting manual - Page 7
7
CTEK D250S Dual Troubleshooting manual - Page 8
8
CTEK D250S Dual Troubleshooting manual - Page 9
9
CTEK D250S Dual Troubleshooting manual - Page 10
10
CTEK D250S Dual Troubleshooting manual - Page 11
11
CTEK D250S Dual Troubleshooting manual - Page 12
12
CTEK D250S Dual Troubleshooting manual - Page 13
13
CTEK D250S Dual Troubleshooting manual - Page 14
14
CTEK D250S Dual Troubleshooting manual - Page 15
15
CTEK D250S Dual Troubleshooting manual - Page 16
16
CTEK D250S Dual Troubleshooting manual - Page 17
17
CTEK D250S Dual Troubleshooting manual - Page 18
18
CTEK D250S Dual Troubleshooting manual - Page 19
19
CTEK D250S Dual Troubleshooting manual - Page 20
20
CTEK D250S Dual Troubleshooting manual - Page 21
21
CTEK D250S Dual Troubleshooting manual - Page 22
22
CTEK D250S Dual Troubleshooting manual - Page 23
23
CTEK D250S Dual Troubleshooting manual - Page 24
24
Trouble Shooting Guide 1
XS 0.8
No LED is lit when the charger is connected only to the battery
Explanation: The plug has to be connected for the LED’s to be lit.
No LED is lit when the charger is connected only to the power outlet
Explanation: One of the LED’s in the bottom row should light up when the
charger is connected to the power outlet.
Test: Make sure that there is power from the power outlet.
No LED’s are lit on the top row when the charger is connected to both the
power outlet and the battery
The LED’s on the bottom row are lit and you can change charging mode. None
of the LED’s the top row on is indicating charging status.
Explanation: The battery voltage could be under 2±0.5V.
Test: Test the charger on a fresh battery.
is flashing
If no battery or if the battery voltage is too low the led will start to flash to
indicate the unit has entered power save mode.
Test: Test the charger on a fresh battery.
is lit
Explanation 1: Reverse polarity.
Test: Make sure that the + cable/clamp is connected to the + terminal and the
cable/clamp is connected to the terminal.
Explanation 2: Loads are connected to the battery which requires more power
than the charger can provide.
Test: Turn off or disconnect the loads when charging.
Explanation 3: The charger is not connected to a 12V battery.
Test: Test with a fresh 12V battery.
Explanation 4: The charge cycle is interrupted in step 1.
Test: Test to restart the charge cycle, if it still fails in step 1 the battery is
sulphated and needs to be replaced.
Explanation 5: The charge cycle is interrupted in step 4.
Test: Test to restart the charge cycle, if it still fails in step 4 the battery is can’t
be charged and needs to be replaced.