ADTRAN netvanta 3430 Quick Start Manual
Download Quick start manual of ADTRAN NetVanta 3430 Network Hardware, Network Router for Free or View it Online on All-Guides.com.
Brand: ADTRAN
Category: Network Hardware , Network Router , Wireless Router
Type: Quick start manual for ADTRAN NetVanta 3430
Pages: 4
1
2
3
4
Quick Start Guide, 61200820E1-13D, November 2009 1
NETVANTA 3430 ROUTER
P/N 1200820E1, 1202820G1
4 Copyright © 2009 ADTRAN, Inc. All Rights Reserved.
GETTING STARTED
Two configuration methods are available for your NetVanta router:
• Web-based graphical user interface (GUI)
• AOS command line interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance, explanations for
each setting, and configuration wizards to help you get started. However, using the AOS CLI may
be necessary for more advanced configurations.
ACCESS THE GUI
You can access the GUI from any Web browser on your network by following these steps:
1. Connect the router to your PC using the ETH 0/1 port on the back of the unit and an
Ethernet cross-over cable.
2. Set your PC to a fixed IP address of 10.10.10.2. To change your PC IP address, navigate to
Computer > Control Panel > Network Connections > Local Area Connection >
Properties > IP (TCP/IP) and select Use this IP Address. Enter these parameters:
IP Address: 10.10.10.2
Subnet Mask: 255.255.255.0
Default Gateway: 10.10.10.1
You do not need to enter any DNS server information. After the information is entered, select
Ok twice, and close the Network Connections dialog box. If you cannot change the PC’s IP
address, you will need to change the unit’s IP address using the CLI. (Refer to the next two
sections for instructions.)
3. Open a Web browser and enter the unit’s IP address in your browser address line as follows:
http://10.10.10.1. The default IP address is 10.10.10.1, but if you had to change the unit’s IP
address using the CLI, enter that address in the browser line.
4. You will then be prompted for the user name and password (the default settings are admin
and password).
5. The initial GUI screen appears. You can access initial setup information by selecting Setup
Wizard from the menu on the left.
ACCESS THE CLI
Access the AOS CLI via the CONSOLE port, a Telnet session, or from the Web GUI. To establish
a connection to the NetVanta router CONSOLE port, you need the following items:
• VT100 terminal or PC (with VT100 terminal emulation software)
• Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end
CONFIGURE YOUR APPLICATION
The applications you will need to configure vary by product and by network. Review the list of
defaults for your unit before deciding what applications to configure. The following are some
common applications that should be configured on startup. These are all available online at
http://kb.adtran.com
.
RESTORING FACTORY DEFAULTS
On units that have a console port, you cannot restore the factory defaults, but must rather erase
the device’s configuration and then re-configure the unit to operate correctly for your network. To
erase the unit’s current configuration, follow these steps:
1. Access the unit’s CLI and enter enable at the > prompt.
2. Enter erase startup-config at the # prompt. The device will have a blank configuration upon
reboot.
3. Enter reload at the # prompt to begin restarting the device. When prompted to save
configuration, enter no. When prompted to reboot, enter yes.
4. Upon reboot you will have to reconfigure the unit using the CONSOLE port. Follow the steps
outlined here or in the technical note, Accessing the Web Interface in AOS, available at
http://kb.adtran.com
(article number 1788).
Configuring T1 Access to a Remote Site
Using PPP in AOS (video article 2003)
Configuring Internet Access (Many to one NAT) with
the Firewall Wizard in AOS (video article 2185)
Configuring Port Forwarding in AOS
(video article 2991)
Configuring QoS for VOIP in AOS
(video article 3091)
Configuring PPP in AOS (article 2523) Configuring HDLC in AOS (article 2152)
Configuring Frame Relay in AOS
(article 2350)
Configuring QoS in AOS
(article 1617)
Configuring DHCP Server in AOS
(article 2419)
Configuring a VPN using Main Mode in AOS
(article 1925)
Configuring a VPN using Aggressive Mode in
AOS (article 1926)
Important: For additional details on product features, specifications,
installation, and safety, refer to the appropriate hardware installation guide on
the AOS Documentation CD shipped with the base unit and available online at
http://kb.adtran.com
.
NETVANTA 3000 SERIES DEFAULTS
Feature Default Value
IP Address 10.10.10.1
Username admin
Password password
HTTP Server Enabled
Event History On
IP Routing Enabled