Sony XM-1652Z Service Manual

Download Service manual of Sony XM-1652Z - Amplifier Amplifier for Free or View it Online on All-Guides.com.

Sony XM-1652Z - Amplifier Service manual - Page 1
1
Sony XM-1652Z - Amplifier Service manual - Page 2
2
Sony XM-1652Z - Amplifier Service manual - Page 3
3
Sony XM-1652Z - Amplifier Service manual - Page 4
4
Sony XM-1652Z - Amplifier Service manual - Page 5
5
Sony XM-1652Z - Amplifier Service manual - Page 6
6
Sony XM-1652Z - Amplifier Service manual - Page 7
7
Sony XM-1652Z - Amplifier Service manual - Page 8
8
Sony XM-1652Z - Amplifier Service manual - Page 9
9
Sony XM-1652Z - Amplifier Service manual - Page 10
10
Sony XM-1652Z - Amplifier Service manual - Page 11
11
Sony XM-1652Z - Amplifier Service manual - Page 12
12
Sony XM-1652Z - Amplifier Service manual - Page 13
13
Sony XM-1652Z - Amplifier Service manual - Page 14
14
Sony XM-1652Z - Amplifier Service manual - Page 15
15
Sony XM-1652Z - Amplifier Service manual - Page 16
16
1
SERVICE MANUAL
US Model
E Model
XM-1652Z
STEREO POWER AMPLIFIER
AUDIO POWER SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
165 watts per channel minimum continuous average power into 4 ohms,
both channels driven from 20 Hz to 20 kHz with no more than 0.04% total
harmonic distortion per Car Audio Ad Hoc Committee standards.
Other Specifications
Circuit system OTL (output transformerless) circuit
Pulse power supply
Inputs RCA pin jacks
High level input connector
Input level adjustment range
0.3 – 6 V (RCA pin jacks),
1.2 – 12 V (High level input)
Outputs Speaker terminals
Speaker impedance 2 – 8 (stereo)
4 – 8 (when used as a bridging amplifier)
Maximum outputs 380 W × 2 (at 4 )
1,000 W (BTL, at 4 )
Rated outputs (supply voltage at 14.4 V)
165 W RMS × 2 (20 Hz – 20 kHz, 0.04% THD+N, at 4 )
200 W RMS × 2 (20 Hz – 20 kHz, 0.1% THD+N, at 2 )
400 W RMS (BTL) (20 Hz – 20 kHz, 0.1% THD+N,
at 4 )
S/N Ratio 93 dBA (reference: 1 W into 4 )
Frequency response 5 Hz – 80 kHz ( dB)
Harmonic distortion 0.008% or less (at 1 kHz, 4 , 10 W)
Low-pass filter 80 Hz, –18 dB/oct
Power requirements 12 V DC car battery
(negative ground)
Power supply voltage 10.5 – 16 V
Current drain at rated output : 40 A (4 , 165 W × 2)
Remote input : 1 mA
Dimensions Approx. 424 × 55 × 290 mm
(16 3/4 × 2 1/4 × 11 1/2 in.) (w/h/d) not incl.
projecting parts and controls
Mass Approx. 4.0 kg (8 lb. 13 oz.) not incl. accessories
Supplied accessories Mounting screws (4)
High level input cord (1)
Protection cap (1)
Design and specifications are subject to change without
notice.
SPECIFICATIONS
+0
–3
Ver. 1.0 2005. 01
9-879-394-01
2005A04-1
© 2005. 01
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation