Maytag cme9010cae Installation Instructions Manual

Download Installation instructions manual of Maytag cme9010cae Microwave Oven for Free or View it Online on All-Guides.com.

Brand: Maytag

Category: Microwave Oven

Type: Installation instructions manual for Maytag cme9010cae

Pages: 17

Download Maytag cme9010cae Installation instructions manual

Maytag cme9010cae Installation instructions manual - Page 1
1
Maytag cme9010cae Installation instructions manual - Page 2
2
Maytag cme9010cae Installation instructions manual - Page 3
3
Maytag cme9010cae Installation instructions manual - Page 4
4
Maytag cme9010cae Installation instructions manual - Page 5
5
Maytag cme9010cae Installation instructions manual - Page 6
6
Maytag cme9010cae Installation instructions manual - Page 7
7
Maytag cme9010cae Installation instructions manual - Page 8
8
Maytag cme9010cae Installation instructions manual - Page 9
9
Maytag cme9010cae Installation instructions manual - Page 10
10
Maytag cme9010cae Installation instructions manual - Page 11
11
Maytag cme9010cae Installation instructions manual - Page 12
12
Maytag cme9010cae Installation instructions manual - Page 13
13
Maytag cme9010cae Installation instructions manual - Page 14
14
Maytag cme9010cae Installation instructions manual - Page 15
15
Maytag cme9010cae Installation instructions manual - Page 16
16
Maytag cme9010cae Installation instructions manual - Page 17
17
240E_JwardsStreet.SE
C',sveland.Tennessee37311
fei:-'23-a72-3333
Fax:_23-478-6716
STEP 8
INSTALLATION CHECKLIST
1. Make sure unit has been installed according to instructions.
2. Remove all packing material from the oven.
3. Replace house fuse or turn breaker back on.
4. Plug power cord into receptacle.
5. Read operating instructions.
6. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR'S USE.
TEMPLATE
NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE INSTRUCTIONS IN THE
INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THE TEMPLATE. THE TEM-
PLATE IS USED TO LOCATE THE POWER CORD CLEARANCE HOLE, CABINET MOUNTING
HOLES AND THE VERTICAL EXHAUST CUTOUT.
1. Determine if your cabinet has a recessed area or has a smooth, flat bottom. See Figure 3. If smooth, tape
template onto the bottom surface (Figure 1). If it is recessed, cut the edges of the template to fit in the
recessed bottom of wall cabinet. Follow directions below for cutting.
RECOMMENDED CUTTING PROCEDURE: Measure thickness of A, B, and C, cut the edge of the tem-
plate to allow for thickness, guideline is marked in 1/4" increments for your convenience.
NOTE: On some cabinets a small bracket or glue block is used between the overhang and the underside of the
cabinet bottom. Cut the template to fit around the bracket or glue block so that template will lie flat against
the cabinet. Tape the Top Cabinet Template to the underside of the top cabinet. See Figure 1.
2. Drill 1/2" diameter holes at D, E and F.
3. If your cabinet has a smooth, flat bottom, cut out the 1 3/4" diameter hole and the 4" x 3/4" slot at G so
that the power cord will not bind when sliding the oven onto the mounting plate. If your cabinet has a recessed
bottom, cut out only the ! 3/4" diameter hole at G for power cord. If cabinets are metal, use the grommet 5.
(See installation hardware in the Installation Instruction Sheet), to surround opening.
4. (SKIP FOR HORIZONTAL EXHAUST OR RECIRCULATING EXHAUST). Cut out shaded area K
through cabinet for Vertical Exhaust location. Exhaust location can be adjusted for a non-recessed cabinet.
5. Remove the top cabinet template.
6. For recessed cabinets, make 3 filler blocks the size of the shaded areas H, I and J, and drill 5/8" diameter
holes through D, E, and F. Place the blocks so that the holes in each block line up with the corresponding
holes in the cabinet. The filler hiocks should be at the same level as the bottom edge of the wall cabinet.
Figure 2.
PROCEED TO INSTALLATION INSTRUCTION SHEET
--_.MA_rA6 Admiral I1 ,,.---.,,J'=._N-_R _el4agie Chef