TO BE REMOVED BYTHE CUSTOMER AFTER iNSTALLATiON IS COMPLETE
f
[] INSTALLATION CHECKOFF LiST
Doors
[] Handles are secure and tight
[] Door seals completely to cabinet on all sides
[] Freezer door is level across the top
Leveling
[] Refrigerator is level, side to side and tilted 1/4" (dmm) front to back
[] Toe grille is properly attached to refrigerator
[] Cabinet is setting solid on all corners
Electrical Power
[] House power turned on
[] Refrigerator plugged in
ice Maker
[] House water supply connected to refrigerator
[] No water leaks present at all connections - recheck in 24 hours
[] Ice Maker is turned ON.
[] Ice & Water Dispenser operates correctly
[] Front filter must be flush with filter housing (some models)
Final Checks
[]
[]
[]
[]
f,*
Shipping material removed
Fresh Food and Freezer controls set
Crisper Humidity controls set
Registration Card sent in
Tools Necessary:
Phillips" head
Quadlex head
screwdllve.r
Socket
Wrench Set
Adiustable
Wrench
1
f
2
HAND TRUCKING
,, Load refrigerator from side of cabinet only•
,, Do not run retaining straps over handles•
,, Do not over-tighten retaining straps•
,, Never use refrigerator handles to move the
refrigerator•
,, Remove tape from doors only after unit is in
place•
SHIPPING MATERIAL
J
1 PIECE OF FOAM
OR CARDBOARD
2 WIRE TIES .....
(Aflwire baskets
will have 2wire
ties)
..........1 PIECE OF TAPE
...... 1 PIECEOF TAPE OR
....... 2 BLUE SHIPPING CLIPS
1 PIECE OF TAPE
SHELF SPACER WITH TOE GRILLE
..... 1 PIECEOF TAPE
..........3 PIECES OF TAPE
.............1 PIECEOF TAPE
Remove Shipping material. (Features may vary per model.)
J
WATER SUPPLY
Connect water supply - check for water leaks•
Turn icemaker OFF if water supply is not
connected immediately. Connecting to a
reverse osmosis system is not recommended.
INSTALLATION CLEARANCES
Allow the following clearances for ease of installation, proper air circulation, and
plumbing and electrical connections:
,, Sides & Top .......... 3/8"
• Back ....................... 1"
k additional information about your refrigerator;
5 "
LEVELING AND ADJUSTING
All four corners of refrigerator must rest firmly on a solid floor. Your
refrigerator has adjustable rollers to help level itand to adjust the doors.
To level cabinet or change door height:
1. Remove toe grille.
2. Use a screwdriver, 3/8" wrench, or nutdriver to adjust the
rollers. To raise cabinet or door, turn screw clockwise. To
lower cabinet or door, turn screw counterclockwise.
RAISE LOWER
: Itooo II ooo
Toe Grille Adjustable FrontRoller _ _,_j
(some models)
CONTROLS
J
Ensure icemaker to turned ON. Check to see that the Ice & Water Dispenser ts operating
_._ co[[ec!!y: !See Automa!ic !ce & We!el Dispense [ Fea!u[es in Use & Care Manua{:) ,
[ "
_, TO REMOVE DOORS (if necessary)
| If you need to remove the doors to get your refrigerator in the house, please See
[,_ Door Removal Instructions in your Use & Care Manual.
I9 '
See "Normal Operating Sights & Sounds" in the Use & Care Manual
so you understand the sounds you may hear once your refrigerator is
running•
Please read entire Use & Care Manual to become aware of important
safety instructions and to become familiar with your new refrigerator.
Send in Registration card to register your refrigerator•
Congratulations! You are ready to enjoy your new refrigerator.
