DANBY Designer DCD5505W-1 Owner's Manual

Download Owner's manual of Danby DCD5505W-1 USA ONLY Dryer for Free or View it Online on All-Guides.com.

Brand: Danby

Category: Dryer

Type: Owner's manual for Danby DCD5505W-1 USA ONLY

Pages: 28 (2.64 Mb)

Download Danby DCD5505W-1 USA ONLY Owner's manual

Danby DCD5505W-1 USA ONLY Owner's manual - Page 1
1
Danby DCD5505W-1 USA ONLY Owner's manual - Page 2
2
Danby DCD5505W-1 USA ONLY Owner's manual - Page 3
3
Danby DCD5505W-1 USA ONLY Owner's manual - Page 4
4
Danby DCD5505W-1 USA ONLY Owner's manual - Page 5
5
Danby DCD5505W-1 USA ONLY Owner's manual - Page 6
6
Danby DCD5505W-1 USA ONLY Owner's manual - Page 7
7
Danby DCD5505W-1 USA ONLY Owner's manual - Page 8
8
Danby DCD5505W-1 USA ONLY Owner's manual - Page 9
9
Danby DCD5505W-1 USA ONLY Owner's manual - Page 10
10
Danby DCD5505W-1 USA ONLY Owner's manual - Page 11
11
Danby DCD5505W-1 USA ONLY Owner's manual - Page 12
12
Danby DCD5505W-1 USA ONLY Owner's manual - Page 13
13
Danby DCD5505W-1 USA ONLY Owner's manual - Page 14
14
Danby DCD5505W-1 USA ONLY Owner's manual - Page 15
15
Danby DCD5505W-1 USA ONLY Owner's manual - Page 16
16
Danby DCD5505W-1 USA ONLY Owner's manual - Page 17
17
Danby DCD5505W-1 USA ONLY Owner's manual - Page 18
18
Danby DCD5505W-1 USA ONLY Owner's manual - Page 19
19
Danby DCD5505W-1 USA ONLY Owner's manual - Page 20
20
Danby DCD5505W-1 USA ONLY Owner's manual - Page 21
21
Danby DCD5505W-1 USA ONLY Owner's manual - Page 22
22
Danby DCD5505W-1 USA ONLY Owner's manual - Page 23
23
Danby DCD5505W-1 USA ONLY Owner's manual - Page 24
24
Danby DCD5505W-1 USA ONLY Owner's manual - Page 25
25
Danby DCD5505W-1 USA ONLY Owner's manual - Page 26
26
Danby DCD5505W-1 USA ONLY Owner's manual - Page 27
27
Danby DCD5505W-1 USA ONLY Owner's manual - Page 28
28
INSTALLATION
Connecting to power supply
IMPORTANT NOTE: This dryer does not come
complete with an electrical power cord Electrical
power cord kits must be purchased by the
consumer and are available at most local
hardware stores Before purchasing a power
cord kit for your dryer, you must first establish
which type of power cord plug is required
(compatible) to fit the electrical receptacle in your
laundary room. i e 3 wire - 4 wire (See Fig. 6)
When purchasing a 3-wire or 4-wire power cord
kit with strain relief, make sure the cord meets
the following requirements:
o UL listed dryer cord kit
- 240 V minimum rated
= 30 A rated
. type SRD or SRDT
minimim five feet long
° closed-loop terminals or open-end spade lugs
with upturned ends
This dryer has a pre-installed (rear mount)
external junction box to facilitate easy connection
of the power cord kit with suitable plug
4-wirereceptacle
(t4-30 R)
3-wire receptacle
(10-30 R)
if you have 4-wire
receptacle, like this. a
4-wire dryer cord must
be purchased locally
If you have 3-wire
receptacle, like this, a
3-wire dryer cord must
be purchased locally
Fig 6
Electrical connection
INSTRUCTIONS
an area where local codes do NOT permit
grounding through the neutral° Use _FOUR-
WIRE CONNECTION_{ instructions.,
Four-wire connection
spade
lerminats with
upturned ends
3/4" U L,4isted NEUTRAL (white)
NEUTRAL strain relief ",.... "_
I
groundprong groundwire -_-"......... ,,'
(green) /
ring terminals
Four-wire power suppfy cord must have four, No-
1 0 copper wires and match a four-wire receptacle
of NEMA Type 1430R The fourlh wire (ground
conductor) must be identified with a green cover
and the neutra! conductor by a whtte cover
Junction box
DO NOT plug end of dryer power cord into a live
receptacle before connecting dryer power cord
to dryer terminals and closing junction/splitter
box as described below,
DO NOT reuse old power supply cord
WARNING:
This dryer is manufactured with the cabinet-
ground conductor connected to the
NEUTRAL (center) of the supply cord at the
terminal block.
Only a 4-conductor cord shall be used when
the appliance is installed in a mobile home or
Fig 7
To connect power cord:
Remove the screws from the cover of the
junction box located at the top rear of the dryer
. Loosen/remove the two screws on the strain
relief clamp and remove from 4-wire supply
cord
o The strain relief splits into two indentical parts,
o insert the large flange of both sections into the
hole iocated on the left side of the junction box
housing The short flange of both sections and
screws must remain positioned on the external
side of the junction box housing
Instructions for Use 7