• Home
• Brands
• Datalogic Manuals
• Datalogic Single Ethernet Cradle Datalogic Memor
• Datalogic Single Ethernet Cradle Memor User Manual

Datalogic Single Ethernet Cradle Memor User Manual

Download Operation & user’s manual of Datalogic Single Ethernet Cradle Datalogic Memor Network Card for Free or View it Online on All-Guides.com.

1

2

Datalogic Memor™ Single Ethernet Cradle

NOTE

Read this manual carefully before performing any type

of connection through the Datalogic Memor™ Single

Ethernet Cradle.

The user is responsible for any damages caused by

incorrect use of the equipment or by inobservance of the

indication supplied in this manual.

NOTE

Do not attempt to disassemble the Datalogic Memor™

Single Ethernet Cradle, as it does not contain parts that

can be repaired by the user. Any tampering will invalidate

the warranty.

The Datalogic Memor™ Single Ethernet Cradle paired with one Datalogic

Memor™ mobile computer builds a reading system for the collection,

decoding and transmission of barcoded data.

The communication between the mobile computer and host PC through

the Datalogic Memor™ Single Ethernet Cradle may occur also by using

the standard ActiveSync® connection.

Figure 1 – Datalogic Memor™ Single Ethernet Cradle

A) LED Indicators

B) Spare Battery Slot

C) Mini USB Connector

D) RS232 Connector

E) Power Jack

F) Ethernet Port with LED indicators

G) Switch Ethernet/USB

The Datalogic Memor™ Single Ethernet Cradle is a serial

communication adapter between the host computer and the Datalogic

Memor™ mobile computer. Power supply is required to be connected to

the Cradle only for ethernet communication.

Since the Datalogic Memor™ Single Ethernet Cradle also functions as a

battery charger, a power supply is required for battery recharging

operations, both for the mobile computer and spare battery pack

recharging. The spare battery pack recharging slot can supply a 1000

mAh as well as a 2000 mAh Battery pac.

822000820

By inserting the Datalogic Memor™ into the cradle, data can be

transmitted to the host and its battery begins charging if the power supply

is connected. In addition, a spare battery can be charged by inserting it

into the slot at the back of the Datalogic Memor™ Single Ethernet Cradle

as shown in the following figure.

Figure 2 – Datalogic Memor™ Single Ethernet Cradle Charging and

Communication

The LEDs positioned on the front part of the Datalogic Memor™

Ethernet Cradle (see figure below) indicate the cradle and spare

battery charger status:

Figure 3 - LED Indicators

Front LED indicators

LED STATUS

Red Constant Spare battery charging*

Charger

Green Constant Spare battery charge

completed

Power

Green it is constant when the

cradle is powered

*

During charging, the LED may turn off to indicate a temporary

suspension of charging.

Ethernet Connector LED Indicators

Solid Green Link established

Flashing Green Link activity

Ethernet

Green LED

(left)

Off No link established

Off 10 Mb connection

Ethernet

Yellow LED

(right)

Solid Yellow 100 Mb connection (this model is not

available)

CONNECTIONS

CAUTION

Connections should always be made with power OFF!

USB CONNECTION

The Datalogic Memor™ Single Ethernet Cradle can be connected to the

host by means of any standard Mini USB cable.

Once the host has been turned on, insert the Datalogic Memor™

mobile computer into the cradle.

Figure 4 - USB Connection

A) Host Computer C) Datalogic Memor™ Single

Ethernet Cradle

B) Std Mini USB (i.e.

94A051016 CAB-421)

D) *Power Supply (only necessary

for battery charging)

* Recommended power supply: 94ACC1324 PG5-30P35 AC/DC

POWER SUPPLY EU/USA PLUG.

NOTE

Be sure that the switch is in the “USB” position.

During switch operation from USB position to Ethernet

position and vice versa the mobile computer must not be

inserted in the cradle.

Spare battery

Charge Slot with

Spare Battery

Inserted

Data Transmission and

Mobile Computer Battery

Charging

Spare Battery

Charger LED

Power LED

A

B

C

D*

A

B

C

D

F

G

E