AGA AMLFDR20 User Instructions
Download User instructions of AGA AMLFDR20 Refrigerator for Free or View it Online on All-Guides.com.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
12
The doors will not close completely
Door blocked open? Move food packages away from door.
Bin or shelf in the way? Push bin or shelf back in the correct
position.
The doors are di cult to open
Gaskets dirty or sticky? Clean gaskets and contact surfaces
with mild soap and warm water. Rinse and dry with soft cloth.
Temperature and Moisture
Temperature is too warm
New installation? Allow 24 hours following installation for the
refrigerator to cool completely.
Door(s) opened often or left open? Allows warm air to enter
refrigerator. Minimize door openings and keep doors fully
closed.
Large load of food added? Allow several hours for
refrigerator to return to normal temperature.
Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in
24 hours. See “Using the Control(s).”
There is interior moisture buildup
NOTE: Some moisture buildup is normal.
Humid room? Contributes to moisture buildup.
Door(s) opened often or left open? Allows humid air to enter
refrigerator. Minimize door openings and keep doors fully
closed.
Ice and Water
The ice maker is not producing ice or not enough ice
Refrigerator connected to a water supply and the supply
shuto
valve turned on? Connect refrigerator to water
supply and turn water shuto
valve fully open.
Kink in the water source line? A kink in the line can reduce
water
w. Straighten the water source line.
Ice maker turned on? Make sure wire shuto arm or switch
(depending on model) is in the ON position.
New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.
Freezer door closed completely? Firmly close the freezer
compartment door. If the freezer compartment door will not
close all the way, see “The doors will not close completely,”
earlier in this section.
Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.
Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.
Water lter installed on the refrigerator? Remove and
operate ice maker. If ice volume improves, then the
ter may
be clogged or incorrectly installed. Replace
lter or reinstall it
correctly.
Reverse osmosis water ration system connected to
your cold water supply? This can decrease water pressure.
See “Water Supply Requirements.”
The ice cubes are hollow or small
NOTE: This is an indication of low water pressure.
Water shuto valve not fully open? Turn the water shuto
valve fully open.
Kink in the water source line? A kink in the line can reduce
water
w. Straighten the water source line.
Water lter installed on the refrigerator? Remove and
operate ice maker. If ice quality improves, then the
lter may
be clogged or incorrectly installed. Replace
lter or reinstall it
correctly.
Reverse osmosis water ration system connected to
your cold water supply? This can decrease water pressure.
See “Water Supply Requirements.”
Questions remain regarding water pressure? Call a
licensed, qual
plumber.
O -taste, odor or gray color in the ice
New plumbing connections? New plumbing connections
can cause discolored or o
- red ice.
Ice stored too long? Discard ice. Wash ice bin. Allow
24 hours for ice maker to make new ice.
Odor transfer from food? Use airtight, moisture proof
packaging to store food.
Are there minerals (such as sulfur) in the water? A water
lter may need to be installed to remove the minerals.
Water lter installed on the refrigerator? Gray or dark
discoloration in ice indicates that the water
ltration system
needs additional
hing. Flush the water system before using
a new water
lter. Replace water when indicated. See
“Water Filtration System.”
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.