• Home
• Brands
• Zenoah Manuals
• Zenoah BC2311LE
• Zenoah BC2311LE Owner's Manual

Zenoah BC2311LE Owner's Manual

Download Owner's manual of Zenoah BC2311LE Brush Cutter for Free or View it Online on All-Guides.com. This version of Zenoah BC2311LE Manual compatible with such list of devices, as: BC2311LE, BC2311LE, BC2611LE, BC2611WE, BC3501LE, BC3501WE, BC4501WE, BC2611LE/WE, BC3501LE/WE, BC4501WE

1

2

3

4

1. Read this manual carefully until you completely

understand and can follow all safety notes,

precautions, and operating instructions before

using of the unit.

2. Do not operate this tool when you are tired, ill,

or under the influence of alchohol, drugs, or

medication.

3. Always wear eye or face protection and

hearing protection.

4. Do not wear loose clothing, jewelry, short

trousers, sandals, or go barefoot. Do not wear

anything which might be caught by branches or

moving part of the unit. Secure hair so it is

above shoulder length.

5. Never start or run the engine inside a closed

room or building. Exhaust gases contain

dangerous carbon monoxide.

6. Before starting the engine, inspect the entire

unit for loose fasteners and fuel leakage. Make

sure that the cutting attachment is properly

installed and securely fastened.

7. Be sure the blade guard is attached in place.

8. Fuel is highly flammable. Always keep open

flames and sparks away from the unit and fuel

depot. Do not smoke while refueling the unit or

mixing fuel.

9. When refueling the unit, make sure to stop the

engine and allow it to cool down. Wipe spilled

fuel completely from the unit. Move at least 3

meters away from fueling site before starting

the engine.

10. Check the condition of working area to avoid

any accident by hitting hidden obstacles such

as stumps, stones, cans, or broken grass.

11. Keep bystanders and animals at least 15

meters away from the operating point, If you

are approached, immediately stop the engine.

For safe operation

848JJ893A0 (709)

OWNER’S MANUAL

15

m

(50ft)

(1) (2) (3) (4) (5) (6) (7)

1

2

(1) Read owner’s manual before operating this machine.

(2) Wear head, eye and ear protection.

(3) Wear foot protection.

(4) Wear gloves.

(5) Beware of thrown objects.

(6) Warning / Attention

(7) Keep all children, bystanders and helpers 15 meters away from the machine.

Explanation of pictorials

ZENOAH CO., LTD.

12. Keep firm footholds and balance at all times.

Do not use the unit where footing is unsteady

or slippery.

13. Keep cutting attachment below waist level.

14. Keep all parts of your body away from the

rotating cutting attachment and hot surfaces.

15. Warn the operator of the danger of blade

thrust. (Kick back)

Blade thrust may occur when the spinning

blade contacts a solid object in the critical

area. A dangerous reaction may occur causing

the entire unit and operator to be thrust

violently. This reaction is called Kick back. As a

result, the operator can lose control of the unit

which can cause serious or fatal injury. Kick

back is more likely to occur in areas where it is

difficult to see the material to be cut.

16. When inspecting or servicing the unit, make

sure to stop the engine and disconnect the

spark plug as necessary.

17. Cover the blade when the transporting or

storing the unit. Secure the unit before for

storage or transporting to prevent loss of fuel,

damage or injury.

18. When replacing cutting attachment or other

components, be sure to use the parts supplied

or recommended by ZENOAH.

19. When the unit is turned off, make sure the

cutting attachment has stopped before the unit

is set down.

20. For units equipped with a clutch, be sure the

cutting attachment stops turning when the

engine idles.

21. Use only for tasks explained in the instruction

handbook.

22. Discard blades that are bent, warped, cracked,

broken or damaged in any way.

23. Instructions on stopping a coasting blade.

A blade can injure while it continues to spin

after the engine is stopped or throttle control is

released.

24. Stop the engine and blade before removing

material that is blocking or entangling the

cutting attachment.

25. Use a sharp blade. A dull blade is more likely

to snag and thrust. Replace the fastening nut

according to the manufacturer's instruction.

26. Cut only material recommended by the

manufacturer. Do not let the blade contact

material it cannot cut, such as rocks, metal etc.

27. Always wear safety boots, additionally a

helmet is required if there is a risk of contact

with falling objects.

Thank you for purchasing a ZENOAH product.

Before using our brushcutter, please read this manual carefully

to understand the proper use of your unit.

1-9 Minamidai, Kawagoe, Saitama, 350-1165 Japan

BRUSHCUTTERS

BC2311LE

BC2611LE/WE

BC3501LE/WE

BC4501WE

If warning label peels off or becomes soiled and

impossible to read, you should contact the dealer

from which you purchased the product to order new

labels and affix them in the required location(s).

IMPORTANT

Never modify your machine.

We won’t warrant the machine, if you use the

remodeled brushcutter or if you don’t observe

the proper usage written in the manual.

WARNING

■ ENGINE

[BC2311LE/BC2611LE/WE]

1. Loosen the bolts temporarily attached to the

clutch housing.

2. Push the drivershaft toward the gearcase and

rotate it by hand to check that the driveshaft is

engaged with the gears.

3. Insert the shaft tube into the clutch housing until

it bottoms. When difficult to engage, twist the

engine slightly.

4. Align the positioning holes on the clutch

housing and the shaft tube and fit the bolt into

the holes. And fasten the tightning bolts by

turns securely.

(Tightning torque: 4.9~7.8N.m. (0.5~0.8kgm))

(1) Positioning hole

(2) Bolt (M5x10)

(3) Tightning bolt (M5x22)

3

Setup