Delfield CAB3-1013 Specifications

Download Specifications of Delfield CAB3-1013 Dispenser for Free or View it Online on All-Guides.com. This version of Delfield CAB3-1013 Manual compatible with such list of devices, as: CAB3-1013, CAB3-1200, CAB3-1450, CAB3-725, CAB3-813

Delfield CAB3-1013 Specifications - Page 1
1
Delfield CAB3-1013 Specifications - Page 2
2
PROJECT
ITEM #
QUANTITY DATE
APPROVAL
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
CAB3
Mobile enclosed three-stack dish dispensers
Short form specications
Cabinet top shall be 16-gauge stainless steel with all corners welded and polished and
reinforced with heavy-gauge channels. Cabinet exterior panels and corner support angles
shall be 20-gauge stainless steel. Unit shall have four 4.00" (10.2cm) diameter polyolen
swivel casters (all locking), and non-marking gray bumpers at each corner.
Dispenser tube shall have 3 vertical side channels and a bottom brace of 22-gauge
stainless steel. Top supporting ange shall be 18-gauge stainless steel . Flange, channels
and bottom brace shall be integrally welded together. Flange shall have 3 guide posts molded
from high impact plastic.
Self-leveling mechanisms shall be eld adjustable by adding or removing stainless steel
extension springs on perimeter of vertical side channels. The dish carrier head shall be
stainless steel welded rods with a removable 18-gauge stainless steel top plate.
Capacity of tubes shall be approximately 72 dishes, with a maximum stacking height of
24.00" (61.0cm).
NOTE: Models without “-ET” or “-QT” sufx are unheated.
THE FOLLOWING APPLIES TO CAB3-ET EVEN TEMP HEATED DISPENSERS ONLY:
Unit shall be supplied with 9' (2.7m) cord and NEMA 5-20P plug. Electrical connections
shall be 120 volt, 60 hertz, single phase.
Each tube shall have its own convection heating module consisting of a single 400 watt
heating element and fan motor, located in the center of the interior bottom cavity. Air intake
shall have a lter. Each tube shall have an adjustable thermostat inside the motor housing
and an ON/OFF switch on one of the dish guide posts. Unit shall maintain temperature
between 120°F–140°F (49°C–60°C).
THE FOLLOWING APPLIES TO CAB3-QT QUICK TEMP HEATED DISPENSERS ONLY:
Unit shall be supplied with 9' (2.7m) cord and NEMA 6-20P plug. Electrical connections
shall be 208-230 volt, 60 hertz, single phase.
Each tube shall have its own convection heating module consisting of a single 700 watt
heating element and fan motor, located in the center of the interior bottom cavity. Air intake
shall have a lter. Each tube shall have an adjustable thermostat inside the motor housing
and an ON/OFF switch on one of the dish guide posts. Unit shall maintain temperature
between 150°F–170°F (66°C–77°C).
Each tube shall have a stainless steel cover.
Optional accessories & modications
Heavy-duty casters (consult factory)
Flange-mount feet in lieu of casters
Special dispenser tube heights
12" (30.5cm) dia. stainless steel dish dispenser tray (CAB3-1200, CAB3-1200-ET and
CAB3-1200-QT only)
Non-marring adjustment rods for oval dishes and various dish diameters (–813
through –1450 sizes only)
Stainless steel cover with access to dishes (–813 through –1450 sizes only; stan-
dard on QT models)
Stainless steel tube cover
Hold-down rod for dispenser tubes
Wrap-around bumpers (adds 1.75" [4.4cm] to overall length and depth)
Fiberglas
®
panels
Laminate panels
Special voltages (consult factory)
Model CAB3-575
with optional wrap-around bumpers