• Home
• Brands
• Yard Machines Manuals
• Yard Machines Y2550 EC
• Yard Machines Y2550 EC Operator's Manual

Yard Machines Y2550 EC Operator's Manual

Download Operator's manual of Yard Machines Y2550 EC Trimmer for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

PART NO. 769-05416 P00 (11/09)

Insert 10' of 0.080"SplitLine

®

through

hole in top of reel. Pull most of line

through hole until 3"-4" remains.

Wind line tightly in direction of arrow.

Split other end of SplitLine

®

back 6"-7".

Push 6"-7" ends into

0.080" holding slots.

Insert or slide lines into the

eyelets in spool. Insert spring

and reel into spool.

Pull lines firmly to release

from holding slots.

Bend short end and push it

into the other hole. Pull tight.

Bump

Knob

Inner

Reel

Spool

Spring

Press primer bulb 10 times.

Put blue choke lever

in Position 1.

Move blue choke

lever to Position 2.

While continuing to

squeeze the throttle

control, move the blue

choke lever to Position 3.

SQUEEZE and HOLD throttle

control for ALL further steps.

Pull the rope

5 times.

Pull the rope 3 to 5

times to start. Run

engine for 30-60

seconds to warm up.

Continue warming for an

additional 60 seconds.

During this time the unit

may be used.

Crouch in starting

position.

DIDN’T START?

Repeat these instructions.

If engine still fails to start, refer

to the Starting/ Stopping

instructions section of this

manual for additional starting

and troubleshooting information.

Quick Instructions to

Replace SplitLine

®

Trimmer Line

Replacement SplitLine

®

Part #49U0134K953

For single line installation,

refer to Line Installation

section of this manual.

For replacement spool

installation, refer to Installing a

Prewound Reel section of this manual.

Quick Instructions

to Start Engine

For complete instructions, refer to

Starting/ Stopping Instructions section

of this manual.

Quick Instructions to

Assemble Trimmers

For complete instructions, refer to the

Assembly Instructions section of this

manual.

Unscrew bump knob

counterclockwise. Remove

inner reel and spring.

5 X

3

"

-4

"

Hold the inner reel in place.

Tighten Bump Knob

clockwise.

IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES BEFORE OPERATING THE UNIT.

Read and understand all instruction, warning and danger labels on the unit.

Put D-handle on shaft.

Move handle a minimum

6 inches away from shaft

grip. Insert clamp bolt and

tighten the wing nut.

Mix thoroughly in a separate fuel can:

– 3.2 fl. oz. of 2-cycle engine oil

– 1 gallon of unleaded gasoline

Place the unit on a level surface. Fill fuel tank.

NOTE: Do not mix directly in the engine fuel tank.

Slide the shield’s slot onto the

mounting bracket. Rotate the

shield onto the shaft. Push

square bolt through shield

and bracket. Tighten washer

and wing nut onto bolt.

While firmly holding the upper

boom, push it straight into the

lower boom and coupler. Tighten

the allen bolt using the 3/16 allen

wrench provided until the lower

swedge boom is firmly in place.

Slot

Bracket

1 Gallon 3.2 oz

40:1

Min. 6"

Español — Page 8 English — Page 2Français — Page 5

NEED HELP? CALL 1–800-800-7310 IN U.S. OR 1–800–668–1238 IN CANADA

Y2550 EC

2-Cycle Trimmer

Operator’s Manual

Electric Starter or Power Start Bit Optional!

THESE OPTIONAL ACCESSORIES ARE SOLD SEPARATELY!

This unit has an alternative starting method that many find easier to use than pulling on a rope.

Please contact a local retailer or call 1-800-800-7310 in the U.S., (1-800-668-1238 in Canada), for more information.

Information may also be found at www.mtdproducts.com or www.mtdproducts.ca