• Home
• Brands
• Yard Machines Manuals
• Yard Machines Y26CS
• Yard Machines Y26CS Operator's Manual

Yard Machines Y26CS Operator's Manual

Download Operator's manual of Yard Machines Y26CS Trimmer for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

PART NO. 769-05304 P00 (11/09)

Quick Instructions to

Replace SplitLine

®

Trimmer Line

For replacement line, call

1-800-800-7310 or go to an

authorized service dealer.

For complete line installation,

refer to Line Replacement

replacement section of the

unit’s manual.

Quick Instructions

to Start Engine

for complete instructions, refer to the

Starting/ Stopping Instructions of the

unit’s manual.

Quick Instructions to

Assemble The Unit

for complete instructions, refer to the

Assembly Instructions of the unit’s

manual.

IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES BEFORE OPERATING THE UNIT.

Read and understand all instruction, warning and danger labels on the unit.

Remove the cap from the

boom. Push the bottom add-on

into the coupler. Turn the knob

clockwise to tighten.

Put D-handle on shaft. Move

handle a minimum 6 inches

away from shaft grip. Insert

clamp bolt and tighten the

wing nut.

Push the cutting attachment shield

down to the top of the gearbox

assembly and rotate the shield to fit into

the recessed pocket. With all holes lined

up insert and tighten the screws to

secure the shield to the gearbox.

Tip unit so that the back of the engine

is facing up in a vertical position.

Remove the oil fill plug from the

crankcase and pour the entire bottle

of 4-cycle oil into the oil fill hole.

NOTE: Do not mix gas and oil

Fill fuel tank with fresh fuel.

Press primer bulb 10x and move

choke lever to Position 1.

Continue to squeeze

throttle control and

move the choke

lever to Position 3.

Move choke lever to

Position 2.

SQUEEZE and HOLD throttle

control for ALL further steps.

Pull the rope

5 times.

Continue squeezing the

throttle control and run unit for

additional 30 to 60 seconds to

complete warm up. The unit

may be used during this time.

Pull starter rope 3 to 5 times.

Making sure to keep throttle

squeezed, run unit for 30-60

seconds to warm up.

Crouch in starting

position.

DIDN’T START?

Repeat these instructions.

If unit still fails to start, refer

to the operator’s manual for

additional starting and

troubleshooting information

5 X

Unleaded

Gasoline

Choke Lever

Primer

Bulb

Choke Lever

Choke Lever

Using 10.5 ft. (3.2 m) of line,

Push or pull the line until the

line is evenly distributed, so

approximately 5 ft. (1.5 m) is

visible from both sides of the

cutting head.

Hold the cutting head knob

and turn the cutting head

clockwise to wind the line

around the spool until 5 in.

(12.7 cm) is protruding from

each side of the cutting head.

Align the arrows on the

cutting head knob with

the outerspool eyelets,

if they are not already.

Cutting

Head

Knob

Arrow

Eyelet

3 to 5 X

Min. 6"

Español — Page 9 English — Page 2Français — Page 5

Operator’s Manual

DO NOT RETURN THIS PRODUCT

For Assistance please call 1-800-800-7310 (U.S.) or 1-800-668-1238 (Canada)

or visit www.mtdproducts.com or www.mtdproducts.ca

NEED HELP? CALL 1-800-800-7310 IN U.S. OR 1–800–668–1238 IN CANADA

Y26CS

4-Cycle Trimmer