Yard Works YW65PFF Instruction Manual

Download Instruction manual of Yard Works YW65PFF Power Pump for Free or View it Online on All-Guides.com.

Brand: Yard Works

Category: Power Pump

Type: Instruction manual for Yard Works YW65PFF

Pages: 19 (0.69 Mb)

Download Yard Works YW65PFF Instruction manual

Yard Works YW65PFF Instruction manual - Page 1
1
Yard Works YW65PFF Instruction manual - Page 2
2
Yard Works YW65PFF Instruction manual - Page 3
3
Yard Works YW65PFF Instruction manual - Page 4
4
Yard Works YW65PFF Instruction manual - Page 5
5
Yard Works YW65PFF Instruction manual - Page 6
6
Yard Works YW65PFF Instruction manual - Page 7
7
Yard Works YW65PFF Instruction manual - Page 8
8
Yard Works YW65PFF Instruction manual - Page 9
9
Yard Works YW65PFF Instruction manual - Page 10
10
Yard Works YW65PFF Instruction manual - Page 11
11
Yard Works YW65PFF Instruction manual - Page 12
12
Yard Works YW65PFF Instruction manual - Page 13
13
Yard Works YW65PFF Instruction manual - Page 14
14
Yard Works YW65PFF Instruction manual - Page 15
15
Yard Works YW65PFF Instruction manual - Page 16
16
Yard Works YW65PFF Instruction manual - Page 17
17
Yard Works YW65PFF Instruction manual - Page 18
18
Yard Works YW65PFF Instruction manual - Page 19
19
SETUP & INSTALLATION (cont.)
11
6. Align and screw the collar of the assembled inlet adaptor onto the thread on the
suction inlet (13) port of the pump (Fig. 5).
Note: Ensure the collar is tightly fastened onto the suction inlet (13); failure to do so
may result in an air leak.
Discharge Outlet
Connecting Hose or Pipe to the Discharge outlet
Note: Keep all hoses short and as straight as possible, failure to do so may decrease the pressure pumps performance.
Caution: All connections must be air tight, failure to do so may result in an air leak which can prevent the pump
from priming. It is recommended that a thread sealant (not included) and/or Teflon tape (not included) is used on
threads to ensure a water tight seal and prevent any leakage.
1. Assemble the 25.4mm (1") hose adaptor (19) by inserting into the
25.4mm (1") collar (Fig. 6).
Note: Ensure the 25.4mm (1") o-ring (21) is fitted into the 25.4mm (1")
collar (18), failure to do so may result in an air leak.
2. Determine which discharge outlet (11) port that will be used. Screw the outlet caps
onto the 2 of the 3 discharge outlets (11) that are not going to be used (Fig. 7).
Note: Multiple outlets can be used to pump water simultaneously but this will result
in lower pressure and flow rate.
Note: If the unused discharge outlets (11) are not blocked off this will result in water
expelling out of the discharge outlet (11).
3. Add thread sealant (not included) and/or Teflon tape (not included) on to the
discharge outlet (11).
4. Align and screw the 25.4mm (1") collar of the assembled outlet adaptor onto the
thread on the discharge outlet (11) port of the pump (Fig. 7).
Note: Ensure the collar is tightly fastened onto the discharge outlet (11); failure to do so may result in an air leak.
Priming
Priming the pump prepares the motor for safe operation.
Caution: Do not run the pump dry. This may result in damage to the pump.
1. Unscrew the priming cap (10) by turning anti-clockwise. Using a hose, fill the
pump by pouring water into the priming hole (Fig. 8).
Note: All open mechanisms (eg: spray nozzle, valves etc.) in the input and output
hose or pipe must be closed before beginning the priming process.
2. Ensure the pump and suction line are full.
3. Replace the priming cap (10) and ensure it is secure.
4. Fully open any shut off mechanisms (eg: spray nozzle, valves etc.) in the input
and output hose or pipe so that the air can escape without obstruction.
Fig. 6
Fig. 7
Fig. 5
Fig. 8