Dell PowerConnect M8428-k Release Note

Download Release notes of Dell M8428-K Chassis, Computer Accessories for Free or View it Online on All-Guides.com. This version of Dell M8428-K Manual compatible with such list of devices, as: M8428-K, PowerEdge M915, PowerEdge M420, PowerEdge M520, PowerEdge M820 Systems

Dell M8428-K Release notes - Page 1
1
Dell M8428-K Release notes - Page 2
2
Dell M8428-K Release notes - Page 3
3
Dell M8428-K Release notes - Page 4
4
Dell M8428-K Release notes - Page 5
5
Dell M8428-K Release notes - Page 6
6
Dell M8428-K Release notes - Page 7
7
Dell M8428-K Release notes - Page 8
8
Dell M8428-K Release notes - Page 9
9
Dell M8428-K Release notes - Page 10
10
Dell M8428-K Release notes - Page 11
11
Dell M8428-K Release notes - Page 12
12
Dell M8428-K Release notes - Page 13
13
Dell M8428-K Release notes - Page 14
14
Dell M8428-K Release notes - Page 15
15
Dell M8428-K Release notes - Page 16
16
Dell M8428-K Release notes - Page 17
17
Dell M8428-K Release notes - Page 18
18
Dell M8428-K Release notes - Page 19
19
Dell M8428-K Release notes - Page 20
20
Dell M8428-K Release notes - Page 21
21
Dell M8428-K Release notes - Page 22
22
Dell M8428-K Release notes - Page 23
23
Dell M8428-K Release notes - Page 24
24
Dell M8428-K Release notes - Page 25
25
Dell M8428-K Release notes - Page 26
26
Dell M8428-K Release notes - Page 27
27
18 System Firmware Version 4.1.0.6
Summary
User Impact
Workaround
Max number of OSPF neighbors not
supported
User confusion over switch
operations.
The maximum number of neighbors is
supported.
Cable fault distance not getting displayed
in WEB in case of cable with one or more
pairs cut or short.
User confusion over switch
operations.
The fault distance is displayed in the web
page.
Ports representation need to be changed
in debug messages
User confusion over switch
operations. Inability to diagnose
network issues.
Ports are now displayed in C/S/P standard
format
No error message for illegal characters in
various command parameters
User confusion over switch
configuration.
The accepted character set and length is
documented in the CLI reference manual.
The ARP entry is not seen in the ARP
table when an ARP reply is sent to DUT.
User confusion over switch
operations. Inability to diagnose
network issues.
ARP entries are stored properly
Mapping Table configuration is not being
displayed on Read-Only mode user web
page.
User confusion over switch
configuration.
The mapping table is displayed for a read-
only user.
ACL is getting deleted when trying to
create max+1 rule.
User confusion over switch
operations. Possible security
issues.
Corrected error checking logic.
LLDP-Med TLV information not
registered for jumbo frame sizes greater
than 8000
User confusion over switch
operations.
Jumbo LLDP frames are now processed
properly
VLAN binding entries are not being
displayed on Read-Only mode user web
page.
User confusion over switch
operations.
VLAN binding entries are available to
read only users
Unable to execute the command dot1x
timeout tx-period 1
User confusion over switch
operations.
This command is accepted with a timeout
period of 1 second. Corrected range check
on input.
In switching> network security >dot1x
authentication web page in read-only user
mode, the Re-Authenticate Now check
box can be checked
User confusion over switch
operations. Possible security issue.
Read-only properties are set for the check
box
System Device information web page
LED information not in sync with front
panel LED information.
No user impact expected.
This issue was regarding various stylistic
aspects of the system device web page.
The system device web page conforms to
the requirements as it exists and does
necessarily match the CLI with regarding
to capitalization or naming conventions
DHCP snooping static binding thru
DHCP request is denied as this is a
expected behavior.
User confusion over switch
operations.
Removed the log message indicating that a
bound DHCP client with an existing
binding sent a DISCOVER. Added a
counter for this condition to the DHCP
debug statistics.
Mode of transfer is displaying
unknown,” while downloading the code
from ftp
User confusion over switch
operations.
ftp transfer mode is displayed
Allow disabling and enabling of terminal
paging
User frustration over switch
configuration.
The terminal length command is now
implemented.
Web does not allow to configure image
descriptor to its max length i.e. 255
characters.
User confusion over switch
operations.
Images descriptors up to 255 characters
are allowed