Dell PowerConnect M8428-k User Manual

Download Operation & user’s manual of Dell M8428-K Chassis, Computer Accessories for Free or View it Online on All-Guides.com. This version of Dell M8428-K Manual compatible with such list of devices, as: M8428-K, PowerEdge M915, PowerEdge M520, PowerEdge M620, PowerEdge M820 Systems

Dell M8428-K Operation & user’s manual - Page 1
1
Dell M8428-K Operation & user’s manual - Page 2
2
Dell M8428-K Operation & user’s manual - Page 3
3
Dell M8428-K Operation & user’s manual - Page 4
4
Dell M8428-K Operation & user’s manual - Page 5
5
Dell M8428-K Operation & user’s manual - Page 6
6
Dell M8428-K Operation & user’s manual - Page 7
7
Dell M8428-K Operation & user’s manual - Page 8
8
Dell M8428-K Operation & user’s manual - Page 9
9
Dell M8428-K Operation & user’s manual - Page 10
10
Dell M8428-K Operation & user’s manual - Page 11
11
Dell M8428-K Operation & user’s manual - Page 12
12
Dell M8428-K Operation & user’s manual - Page 13
13
Dell M8428-K Operation & user’s manual - Page 14
14
Dell M8428-K Operation & user’s manual - Page 15
15
Dell M8428-K Operation & user’s manual - Page 16
16
Dell M8428-K Operation & user’s manual - Page 17
17
Dell M8428-K Operation & user’s manual - Page 18
18
Dell M8428-K Operation & user’s manual - Page 19
19
Dell M8428-K Operation & user’s manual - Page 20
20
Dell M8428-K Operation & user’s manual - Page 21
21
Dell M8428-K Operation & user’s manual - Page 22
22
Dell M8428-K Operation & user’s manual - Page 23
23
Dell -10GbE PTM Rev 1.0
13
2.4.4 Mechanical Installation
2.4.4.1 To install the PTM
1. Make sure that there is no foreign matter or dirt in the back plane connector or in the chassis slot.
2. Push the PTM into the chassis. Make sure that the ears on the latch hook onto the latching bar.
3. Push the latch handle towards the orange latch release until it locks.
2.4.4.2 To remove the PTM
1. Push the orange latch release and the latch handle will pop out
2. Pull the handle out until it is 90 degrees from the front of the PTM.
3. Pull the PTM out of the chassis.
2.4.5 Cable Installation
All cables can be inserted or removed with the unit powered on. To insert a cable, press the con-
nector into the port receptacle until the connector is firmly seated. The GREEN LED indicator,
above each SFP+ port, will light when the physical connection is established (that is, when the unit
is powered on and a cable is plugged into the port with the other end of the connector plugged into
a functioning port). After plugging in a cable, lock the connector using the latching mechanism
particular to the cable vendor. When a logical connection is made the yellow light will come on.
When data is being transferred the yellow light will blink.
To remove, disengage the locks and slowly pull the connector away from the port receptacle. Both
LED indicators will turn off when the cable is unseated.
Cable lengths should be used which allow for routing horizontally around to the side of the chassis
before bending upward or downward in the rack.
CLASS 1 LASER PRODUCT and reference to the most recent laser
standards:
IEC 60825-1:2007/03 y EN 60825-1:2007
Always install and remove cables by pushing or pulling the cable and
connector in a straight line with the pass through module.
Cables, especially long copper cables, can weigh a substantial amount.
Make sure that the weight of the cable is supported on its own and not
hanging from the pass through module.