Dell PowerVault LTO3-060 User Manual

Download Operation & user’s manual of Dell PowerVault LTO3-060 Software, Storage for Free or View it Online on All-Guides.com.

Brand: Dell

Category: Software , Storage

Type: Operation & user’s manual for Dell PowerVault LTO3-060

Pages: 36 (0.56 Mb)

Download Dell PowerVault LTO3-060 Operation & user’s manual

Dell PowerVault LTO3-060 Operation & user’s manual - Page 1
1
Dell PowerVault LTO3-060 Operation & user’s manual - Page 2
2
Dell PowerVault LTO3-060 Operation & user’s manual - Page 3
3
Dell PowerVault LTO3-060 Operation & user’s manual - Page 4
4
Dell PowerVault LTO3-060 Operation & user’s manual - Page 5
5
Dell PowerVault LTO3-060 Operation & user’s manual - Page 6
6
Dell PowerVault LTO3-060 Operation & user’s manual - Page 7
7
Dell PowerVault LTO3-060 Operation & user’s manual - Page 8
8
Dell PowerVault LTO3-060 Operation & user’s manual - Page 9
9
Dell PowerVault LTO3-060 Operation & user’s manual - Page 10
10
Dell PowerVault LTO3-060 Operation & user’s manual - Page 11
11
Dell PowerVault LTO3-060 Operation & user’s manual - Page 12
12
Dell PowerVault LTO3-060 Operation & user’s manual - Page 13
13
Dell PowerVault LTO3-060 Operation & user’s manual - Page 14
14
Dell PowerVault LTO3-060 Operation & user’s manual - Page 15
15
Dell PowerVault LTO3-060 Operation & user’s manual - Page 16
16
Dell PowerVault LTO3-060 Operation & user’s manual - Page 17
17
Dell PowerVault LTO3-060 Operation & user’s manual - Page 18
18
Dell PowerVault LTO3-060 Operation & user’s manual - Page 19
19
Dell PowerVault LTO3-060 Operation & user’s manual - Page 20
20
Dell PowerVault LTO3-060 Operation & user’s manual - Page 21
21
Dell PowerVault LTO3-060 Operation & user’s manual - Page 22
22
Dell PowerVault LTO3-060 Operation & user’s manual - Page 23
23
Dell PowerVault LTO3-060 Operation & user’s manual - Page 24
24
Dell PowerVault LTO3-060 Operation & user’s manual - Page 25
25
Dell PowerVault LTO3-060 Operation & user’s manual - Page 26
26
Dell PowerVault LTO3-060 Operation & user’s manual - Page 27
27
Dell PowerVault LTO3-060 Operation & user’s manual - Page 28
28
Dell PowerVault LTO3-060 Operation & user’s manual - Page 29
29
Dell PowerVault LTO3-060 Operation & user’s manual - Page 30
30
Dell PowerVault LTO3-060 Operation & user’s manual - Page 31
31
Dell PowerVault LTO3-060 Operation & user’s manual - Page 32
32
Dell PowerVault LTO3-060 Operation & user’s manual - Page 33
33
Dell PowerVault LTO3-060 Operation & user’s manual - Page 34
34
Dell PowerVault LTO3-060 Operation & user’s manual - Page 35
35
Dell PowerVault LTO3-060 Operation & user’s manual - Page 36
36
Step 2 Removing Power from the System
1. Power-off the system.
2. Disconnect the power cord from both the electrical outlet and the system.
Step 3 Setting the SCSI ID
Your tape drive is shipped with a default SCSI ID of 6, but it can be assigned any unused ID between 0 and 15. Do not use SCSI ID 7, which is reserved for the
SCSI controller, or SCSI ID 0, which is typically assigned to the boot disk. We do not recommend installing the drive onto a narrow SCSI bus, as this will restrict
performance.
To set the SCSI ID:
1. Locate the SCSI ID connector (see number 2 in Figure 3 in the Introduction. The SCSI ID is set using jumpers on a set of pins at the rear of the drive.
2. Determine whether you need to change the SCSI ID from the default of 6. Make sure the ID is not used by another device.
3. Referring to Figure 5, find the ID number that you chose. Then, place jumpers on the connector pins as shown (use a pair of needle-nose pliers to connect the
jumpers to the pins that are shaded).
Figure 5. SCSI Connector Pins
Step 4 Preparing the Mounting Bay in Your System
Refer to your system's documentation for instructions on how to prepare the mounting bay to receive the tape drive.
Step 5 Attaching Mounting Hardware
If your system requires special rails or other hardware to install the tape drive, mount them on the tape drive in this step.
If your system does not require special mounting hardware, proceed to step 6.
Step 6 Installing the Drive
Slide the tape drive into the open bay, aligning the tray or rails with the slots in the bay, as shown in Figure 6.
Figure 6. Install the Drive
NOTICE: Static electricity can damage electronic components. Always wear an antistatic wriststrap if possible. If not, to equalize the electromagnetic
charges, touch a bare metal part of the computer (such as the back plate) before you remove the tape drive from its bag.
CAUTION: To avoid personal injury or damage to the system or tape drive, ensure that the system power cord is disconnected before you
install the drive.