Delta 31-460 Instruction Manual

Download Instruction manual of Delta 31-460 Sander for Free or View it Online on All-Guides.com.

Brand: Delta

Category: Sander

Type: Instruction manual for Delta 31-460

Pages: 20 (1 Mb)

Download Delta 31-460 Instruction manual

Delta 31-460 Instruction manual - Page 1
1
Delta 31-460 Instruction manual - Page 2
2
Delta 31-460 Instruction manual - Page 3
3
Delta 31-460 Instruction manual - Page 4
4
Delta 31-460 Instruction manual - Page 5
5
Delta 31-460 Instruction manual - Page 6
6
Delta 31-460 Instruction manual - Page 7
7
Delta 31-460 Instruction manual - Page 8
8
Delta 31-460 Instruction manual - Page 9
9
Delta 31-460 Instruction manual - Page 10
10
Delta 31-460 Instruction manual - Page 11
11
Delta 31-460 Instruction manual - Page 12
12
Delta 31-460 Instruction manual - Page 13
13
Delta 31-460 Instruction manual - Page 14
14
Delta 31-460 Instruction manual - Page 15
15
Delta 31-460 Instruction manual - Page 16
16
Delta 31-460 Instruction manual - Page 17
17
Delta 31-460 Instruction manual - Page 18
18
Delta 31-460 Instruction manual - Page 19
19
Delta 31-460 Instruction manual - Page 20
20
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which
has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an
extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause
a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct gauge to use depending
on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
EXTENSION CORDS
OPERATING INSTRUCTIONS
FOREWORD
The Delta Model 31-460 is a 4" Belt; 6" Disc Sander and comes equipped with; 1/3 hp 120 Volt Single Phase Induction
Motor, tilting table, miter gage, backstop, 4" x 36" 60 grit sanding belt and 6" 60 grit sanding disc. The tilting aluminum
table can be mounted for use on either the belt or disc unit. Belt operates horizontal, vertical and at any angle in
between. The 3100 rpm disc and 2000 sf/m belt speed will handle just about any sanding job in hard and soft wood.
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,
gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
5
Fig. D
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere Total Length Gauge of
Rating Volts of Cord in Feet Extension Cord
0-6 120
up to
25 18 AWG
0-6 120 25-50 16 AWG
0-6 120 50-100 16 AWG
0-6 120 100-150 14 AWG
6-10 120
up to
25 18 AWG
6-10 120 25-50 16 AWG
6-10 120 50-100 14 AWG
6-10 120 100-150 12 AWG
10-12 120
up to
25 16 AWG
10-12 120 25-50 16 AWG
10-12 120 50-100 14 AWG
10-12 120 100-150 12 AWG
12-16 120
up to
25 14 AWG
12-16 120 25-50 12 AWG
12-16 120
GREATER THAN 50 FEET NOT RECOMMENDED