• Home
• Brands
• Delta Electronics Manuals
• Delta Electronics DTE10P
• Delta Electronics Temperature Controller DTE Instruction Manual

Delta Electronics Temperature Controller DTE Instruction Manual

Download Instruction sheet of Delta Electronics DTE10P Controller, Power Supply for Free or View it Online on All-Guides.com. This version of Delta Electronics DTE10P Manual compatible with such list of devices, as: DTE10P, DTE20C, DTE20P, DTE20V, Temperature Controller DTE

1

2

Series Temperature Controller

Instruction Sheet

Thank you very much for choosing Delta DTE series temperature controller. Please read this instruction sheet carefully before

using your DTE to ensure proper operation. Keep this instruction sheet handy for quick reference.

 Warning

DANGER! CAUTION! ELECTRIC SHOCK!

DTE is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust,

humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from

operating the device (e.g. key or specific tools are required for opening the enclosure) in case danger and

damage on the device may occur.

1. Prevent dust or metallic debris from falling into the device and cause malfunctions. DO NOT

modify or uninstall the circuit

board of DTE without being permitted. DO NOT

use empty terminals.

2. Keep away from high-voltage and high-frequency environment during the installation in case of interference. Prevent using

the device in premises which contain:

(a) dust or corrosive gas; (b) high humidity and high radiation; (c) shock and vibration.

3. The power has to be switched off when wiring or changing the temperature sensor.

4. When installing the circuit board of the accessory, please make sure the power of the main unit is switched off and insert

the accessory into the correct slot on the main unit.

5. Make sure to use compensation wire which matches the thermocouple or platinum resistance when extending or

connecting the thermocouple or platinum resistance.

6. Keep the wire as short as possible when wiring a sensor to the controller. Separate the power cable and load wire in order

to prevent interference and induced noise.

7. Make sure the power cables and signal device are installed correctly before switching on the power; otherwise serious

damage may occur.

8. DO NOT

touch the terminal or repair the device when the power is on; otherwise an electric shock may occur.

9. Please wait for 1 minute after the power is switched off to allow the capacitor to discharge and DO NOT

touch the internal

wiring within this period.

10. DO NOT

touch the internal terminal when DTE is either switched on or off in case you may damage the circuit.

11. Please place DTE with other heating objects (e.g. power supply) within proper distance while installing DTE.

 Ordering Information!

Series name DTE: Delta E series temperature controller

1 Device type

1: main unit 2: accessory

2 3

0T: 4-channel TC

0P: 4-channel PT

0T: 4-channel TC

0P: 4-channel PT

0V: 4 channels of voltage pulse output

0C: 4 channels of linear current output

0R: 4 channels of relay output

0L: 4 channels of linear voltage output

CT: 4 channels of current transformer sensors

DS: Display and setup module

 Functions & Electrical Specifications!

Power input DC 24V, isolated switching power supply

Voltage range 90% ~ 110% rated voltage

Power consumption Max. 10W + 3W × number of DTC2000 controllers connected in parallel (Max. 7)

Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK

Input sensor

Platinum resistance: Pt100, JPt100, Cu50

Sampling cycle Thermocouple or platinum resistance: 1.0 second/all input

Control method PID, PID programmable, manual, ON/OFF

Relay output: SPST, Max. AC 250V load, 3A resistive load

Voltage pulse output: DC 24V, Max. 40mA current output

Current output: DC 4 ~ 20mA output (resistive load < 500Ω); for OUT1 and OUT2 only

Output accessories

(optional)

Analog voltage output: 0 ~ 10V (resistive load > 1,000Ω); for OUT1 and OUT2 only

Output functions

Control output, alarm output or proportional output (proportional output is only applicable in

the model with linear voltage and current output for OUT1, OUT2)

Alarm modes 12 alarm modes available

Communication RS-485 digital communication; supports baud rate 2,400bps ~ 115,200bps

Communication

protocol

Supports Modbus ASCII/RTU

Extension port

The extension port transmits 24V power supply and communication signals to extension

module DTC2000.

Vibration resistance 10 ~ 55Hz 10m/s

2

3 axes 10mins

Shock resistance Max. 300m/s

2

3 axes 6 directions, 3 times each

Ambient temperature 0°C ~ +50°C

Storage temperature -20°C ~ +65°C

Operation altitude < 2,000m

Ambient humidity 35% to 85% RH (non-condensing)

Pollution degree 2

 Product Profile & Outline!

DTE10T/P

1 I/O terminals

2 Status LED

3 Display and setup unit

4 DIN rail clip

5 Power input port

6 RS-485 communication port

7 Extension module fixing clip

8 Extension port

 Panel Layout!

 Input

The standard DTE main unit is attached with 4 channels of inputs. You can purchase additional DTE20T or DTE20P to expand

the number of input channels. DTE supports maximum 8 channels of inputs which belong to group INA and group INB. Each

group possesses 4 input channels.

DTE series supports the following input sensors:

Input Sensor Type Register Value Range

For DTE10P / DTE20P

Temperature measurement resistance (Cu50) 13 -50 ~ 150°C

Platinum resistance (Pt100) 12 -200 ~ 600°C

Platinum resistance (JPt100) 11 -20 ~ 400°C

For DTE10T / DTE20T

Thermocouple TXK type 10 -200 ~ 800°C

Thermocouple U type 9 -200 ~ 500°C

Thermocouple L type 8 -200 ~ 850°C

Thermocouple B type 7 100 ~ 1,800°C

Thermocouple S type 6 0 ~ 1,700°C

Thermocouple R type 5 0 ~ 1,700°C

Thermocouple N type 4 -200 ~ 1,300°C

Thermocouple E type 3 0 ~ 600°C

Thermocouple T type 2 -200 ~ 400°C

Thermocouple J type 1 -100 ~ 1,200°C

Thermocouple K type 0 -200 ~ 1,300°C

Note: The default setting in DTE10T is “thermocouple K type”. The default setting in DTE10P is “Pt100".

Communication address: Input sensor types at H10A0 ~ H10A7; input upper limits at H1010 ~ H1017; input lower limits at

H1018 ~ H101F.

 Output

DTE supports maximum 16 channels of outputs, belonging to output groups OUT1, OUT2, SUB1 and SUB2, each group with 4

channels. See the explanations below for how input channels correspond to output groups.

 Without group INB (4 channels of input): Every channel corresponds to 2 groups of output and 2 groups of alarms. OUT1 and

SUB1 are for control output, and OUT1 can be used for proportional output. OUT2 and SUB2 are fixed for alarm output.

 With group INB (8 channels of input): Every channel is paired with 2 groups of outputs. OUT1 and OUT2 are used for control

output or proportional output of CH1 ~ CH8. SUB1 and SUB2 are used for control output or alarm output.

See Table 1 for the relations between input and output.

4 channels of input 8 channels of input

Output Group INA (CH1 ~ CH4) INA (CH1 ~ CH4) INB (CH5 ~ CH8)

OUT1

Main control output or

proportional output

Main control output or proportional

output

No corresponding output

OUT2 Alarm 1 output No corresponding output

Main control output or proportional

output

SUB1 Control output Control output or alarm output No corresponding output

SUB2 Alarm 2 output No corresponding output Control output or alarm output

Table 1

Note: SUB1 and SUB2 do not support DTE20L and DTE20C. Please install the optional output modules you purchase into

the correct slot.

Communication Address of Output & How to Set up Parameters:

See Table 2 for the communication addresses of output and Table 3 for the definition of the value in the address.

INA INB

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

OUT1, OUT2 H10A8 H10A9 H10AA H10AB H10AC H10AD H10AE H10AF

SUB1, SUB2 H10B0 H10B1 H10B2 H10B3 H10B4 H10B5 H10B6 H10B7

Table 2

Value = 0 Value = 1 Value = 2 Value = 3

OUT1, OUT2** Heating control Cooling control Proportional output Disable output

SUB1, SUB2** Heating control Cooling control Alarm output* Disable output

Table 3

*When there are only 4 channels of inputs, SUB1 cannot be used for alarm output but heating/cooling control only.

**When there are only 4 channels of inputs, OUT2 and SUB2 cannot be set up by the user but set up automatically as "alarm

output” by the controller.

Control Output:

DTE offers PID control, ON/OFF control, manual control and programmable PID control. Control output methods are set at

address H10B8 ~ H10BF (default = 0: PID), PID parameters at H1028 ~ H105F, ON/OFF parameters at H1058 ~ H106F, and

manual control parameters at H1070 ~ H107F.

Alarm Output:

DTE offers 12 alarm modes. The alarm modes are set up at address H10C0 ~ H10C7, upper limits at H1080 ~ H1087 and

lower limits at H1088 ~ H108F.

SV Alarm Mode Alarm Output Operation

0 No alarm Off

1

Alarm output is enabled when the temperature reaches upper and lower

limits: The alarm will be enabled when PV exceeds SV + AL-H or falls below

SV – AL-L.

ON

OFF

AL-L SV AL-H

2

Alarm output will be enabled when the temperature reaches the upper limit:

The alarm will be enabled when the PV exceeds SV + AL-H.

ON

OFF

SV

AL-H

3

Alarm output will be enabled when the temperature reaches the lower limit:

The alarm will be enabled when the PV falls below SV – AL-L.

ON

OFF

AL-L

SV

4

Alarm output will be enabled when the PV is between SV + AL-H and SV –

AL-L.

ON

OFF

AL-L SV

AL-H

5

Alarm output will be enabled when the temperature reaches the absolute

value of the upper and lower limits: The alarm will be enabled when the PV

exceeds AL-H or falls below AL-L.

ON

OFF

AL-L

AL-H

6

Alarm output will be enabled when the temperature reaches the absolute

value of the upper limit: The alarm will be enabled when the PV exceeds

AL-H.

ON

OFF

AL-H

7

Alarm output will be enabled when the temperature reaches the absolute

value of the lower limit: The alarm will be enabled when the PV falls below

AL-L.

ON

OFF

AL-L

8

Upper/lower limit standby alarm: The alarm will be enabled when the PV

reaches SV and further exceeds SV + AL-H or falls below SV – AL-L.

ON

OFF

AL-L

AL-H

SV

9

Upper limit standby alarm: The alarm will be enabled when the PV reaches

SV and further exceeds SV + AL-H.

ON

OFF

SV AL-H

10

Lower limit standby alarm: The alarm will be enabled when the PV reaches

SV and further falls below SV – AL-L.

ON

OFF

AL-L SV

11

Upper limit hysteresis alarm: The alarm will be enabled when the PV exceeds

SV + AL-H. The alarm will be disabled when the PV falls below SV + AL-L.

ON

OFF

AL-L

AL-H

12

Lower limit hysteresis alarm: The alarm will be enabled when the PV falls

below SV – AL-H. The alarm will be disabled when the PV exceeds SV –

AL-L.

ON

OFF

AL-L

AL-H

 LED Display

PWR: On B DTE is powered.

RUN: On B Any of the channel is executing.

COM: Flashing B Communication in progress

ERR: Indicating errors (red)

ERR LED is on indicates one of the following errors occur, and the output has to be disabled.

1. Memory EEPROM error.

2. Any of the input points is not connected.

3. Any of the input points exceeds the setup range.

4. Any of the input temperatures has not been stabilized.

 Synchronous Communication Protocol & Auto ID Setup

This function allows the auto setup of communication protocol in extension module DTC2000 and DTC2001 following the

communication protocol set in the DTE main unit. The station IDs of DTC decrease. See below for the steps.

1. Set the auto communication ID of DTE as “1” (communication address: H10F8).

2. Switch off DTE. Connect DTE with extension module DTC2000, DTC2001 and switch on DTE again.

3. Default communication protocol: 9,600bps, 7 bits, Even, 1 stop bit, communication address = 01.