UNIVERSAL REMOTE CONTROL UR5U-8820L Operating Instructions

Download Operating instructions of Universal Remote Control UR5U-8820L Other for Free or View it Online on All-Guides.com.

Universal Remote Control UR5U-8820L Operating instructions - Page 1
1
Universal Remote Control UR5U-8820L Operating instructions - Page 2
2
Button Functions
4
Programming the Remote Control
5
There are two ways you can program your
CLIKR
TM
-5
remote:
*
The Pre-Programmed 3-Digit Code Method
*
The Auto-Search Method
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Auto-Search Method scans through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, a component LED will light for
30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit setup
mode and you will need to start over.
A. Pre-Programmed 3-Digit Code Method
STEP1
Turn on the Component you want to program (TV, VCR, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV, VCR,
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED light will
turn on for 30 seconds indicating the unit
is ready to be programmed.
STEP3 Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
*Note : If the 3-digit code number you just entered
is correct, the Component will turn Off. If
it did not turn Off, continue entering code
numbers listed for that brand until the
Component turns Off.
STEP4 After you’ve entered the correct code
number and the Component has turned
Off, press the [POWER] button to turn the
Component back On. Now it’s time to test
the VOLUME and MUTE buttons for the
TV (or PLAY and STOP buttons for VCR
and DVD) to make sure they all work. If
any of the functions do not work as they
should, repeat from STEP 3 using the next
3-digit code number listed for that brand.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the same
[COMPONENT] button one more time.
The Component LED light will blink twice
to confirm that the code was successfully
stored.
Now, program the rest of your Components by
repeating STEPS 1-5.
*Note : If the Pre-Programmed Method did not
work, or if the Code Tables do not list
your Component brand, use the Auto-
Search Method as explained in Section B.
B. Auto-Search Method
STEP1 Turn on the Component you want to
program (TV, VCR, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV, VCR,
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED light will
turn on for 30 seconds indicating the unit
is ready to be programmed.
STEP3 Point the remote toward the Component
and press the [CH] or [CH] button one
step at a time or keep it pressed. The
remote will emit a series of ON/OFF
commands. Release the [CH] or [CH]
button as soon as the Component turns Off.
STEP4
Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any
of the functions do not work as they
should, repeat from STEP 3 using [CH] or
[CH] buttons to find the correct code.
STEP5
Save the code. (Same as for 3-Digit Code
Programming Method - Section A).
Now, repeat the Auto-Search Method for those
Components you could not program earlier with the
Pre-Programmed Method.
C. Finding a Component Button’s
Setup Code Number
If you used the Auto-Search Method to program a
Component, you may not know what the correct code
number is. Here is a way for you to identify the code
number, so you can record it for future reference.
STEP1
Press the [COMPONENT] button (TV, VCR, DVD
or AUX) you want to verify and the [OK/SEL]
button simultaneously for 3 seconds. The
Component LED light will turn on for 30 seconds.
STEP2
Press the [INFO] button and count the number
of times the Component LED light blinks. This
number indicates the first digit of the code,
followed by the second and third, each
separated by a one second pause when the
LED will turn off.
*Note
: 10 blinks represents the number zero.
Example : One blink, (pause), eight blinks, ( pause)
and three blinks, indicates code number 183.
D. AUX Function: Programming a 5
th
Component
You can take advantage of the AUX function to program
a 5
th
Component such as a second TV, VCR, DVD or
Audio Component.
STEP1
Turn on the 5
th
Component you want to
program (TV, VCR, DVD or Audio).
STEP2
Press the [AUX] button and the [OK/SEL] button
simultaneously for 3 seconds.The [AUX]
Component LED will turn on for 30 seconds.
STEP3
Press the [COMPONENT] button you want to
setup. Point the remote control toward the
Component and enter the 3-digit code number
assigned to your brand.
*Note : If the 3-digit code number you just entered is
the correct number, the Component will turn
Off. If it did not turn Off, continue entering
code numbers listed for that brand until the
Component turns Off
STEP4
Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any of
the functions do not work as they should, you
need to find a new code.
STEP5
Once you have found the correct 3-digit code,
save it by pressing the [AUX] button one more
time. The Component LED light will blink twice
to confirm the code was stored. Now when
you press the AUX button, all the buttons will
work with that 5
th
Component.
E. Programming the System On/Off Button
This allows you to program the System On/Off button so
it can send up to five power On/Off commands with one
button press.
STEP1
Press the [CBL] button.
STEP2
Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3 seconds.
The [CBL] button will turn on for 30 seconds.
STEP3
Press the first [COMPONENT] button you want
to store in the [SYSTEM ON/OFF] button and
then the [POWER] button. Repeat this for
other Components until you have stored all the
desired power commands into the [SYSTEM
ON/OFF] button.
STEP4
Press the [CH+] button to save the power
commands you stored. The [CBL] button will
blink twice to confirm the commands have
been saved.
F. Programming Channel Control
You can program the channel controls (Channel Up,
Channel Down, Last and Numbers) from one Component
to operate in another Component mode. Default channel
control settings on the remote control are as follows:
CBL : CBL T V : CBL VCR : CBL
DVD : DVD AUX : AUX
If you wish to store the TV channel control in TV mode,
use the following steps.
STEP1
Press the [TV] button and the [OK/SEL] button
simultaneously for 3 seconds. The [TV]
Component LED will turn on for 30 seconds.
STEP2
Press the [VOL -] button.
STEP3
Press the [TV] button again.
The Component LED will blink twice to confirm
the programming.
To return to original state:
If you wish to restore the CABLE channel
control in TV mode, repeat the above steps but
press [CBL] in STEP3 .
G. Programming Volume Control
You can program the volume controls (Volume Up,
Volume Down and Mute) from one Component to
operate in another Component mode. Default volume
control settings on the remote control are as follows:
CBL : CBL T V :TV VCR :TV
DVD :TV AUX : AUX
If you wish to store the TV volume control in CBL
mode, use the following steps.
STEP1
Press the [CBL] button and the [OK/SEL]
button simultaneously for 3 seconds. The
[CBL] Component LED will turn on for 30
seconds.
Universal Remote Control, Inc.
www.universalremote.com
OCE-0052D REV 02 (04/30/07)
UR5U-8820L
Operating Instructions For
CLIKR
-5
Cable Remote Control
The CLIKR
TM
-5 UR5U-8820 is designed to
operate the Motorola, Scientific-Atlanta,
Pioneer, Pace Micro and Samsung digital
set tops, plus the majority of TV, VCR, DVD
and AUDIO equipment on the market as
shown below.
CABLE : Cable Converters TV : Televisions
VCR : VCRs and TV/VCRs DVD : DVD Players
AUX : Audio Receivers and DVRs, etc.
Introduction
1
DEFAULT STATE:
Component Default: CABLE
Channel Default: CABLE channel and
numbers through the CABLE. You have the
option of controlling your CABLE channel and
numbers through the TV or VCR. Refer to
section F for programming steps.
Volume Default: CABLE volume and mute
through the CABLE. You have the option of
controlling your CABLE volume and mute
through the TV, VCR or DVD. Refer to section
G for programming steps.
Operations
3
Replacing Batteries
2
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
STEP2
Press the [VOL +] button.
STEP3
Press the [TV] button.
The Component LED will blink twice to
confirm the programming.
To return to original state:
If you wish to restore the CBL volume control in CBL mode,
repeat the above steps but press [CBL] in
STEP3
.
H. Programming a ‘Macro’ button
In CABLE mode, the M button can be programmed to
act as a ‘Macro’ . This allows you to program from
one up to three separate channels that can be
accessed by simply pressing the programmed
Macro button.
STEP1
Press the [CBL] button to select the CBL
mode.
STEP2
Press the [M] button and [OK/SEL] button
simultaneously for 3 seconds. The [CBL]
button will turn on for 30 seconds.
STEP3
Enter the 3 or 4-digit code for the channel
you want programmed first (for example,
007) using the Number Pad, then press the
[STOP] button. Then enter the code for the
next channel (for example, 050), then press
the [STOP] button. Repeat this process for
the third channel. The [CBL] button will blink
once for each channel entered.
STEP4
Press the [CH+] button to store the channels
that were selected. The [CBL] button will
blink twice to confirm the storage of
commands.
To access the programmed channels, press the [M]
button once. This will bring up the first channel. Press
once again and it will bring up the second channel.
Press again and it will bring up the third channel.
I. Low Battery Warning
When the batteries are low and need to be replaced
with fresh batteries, the Component LED lights will
blink 2 times in sequence whenever a [POWER]
button is pressed to turn on equipment.
J. Memory Lock System
This remote control is designed to retain programmed
memory for 10 years even after batteries are removed
from the remote control.
K. Record Your Component Set-up Codes
TV Set-up Code Number:
VCR Set-up Code Number:
DVD Set-up Code Number:
AUX Set-up Code Number: