US Robotics USR8054 Quick Installation Manual
Download Quick installation manual of US Robotics USR8054 Network Card, Wireless Access Point for Free or View it Online on All-Guides.com.
Brand: US Robotics
Category: Network Card , Wireless Access Point , Wireless Router
Type: Quick installation manual for US Robotics USR8054
Pages: 2 (0.15 Mb)
1
2
Before You Begin
Note: Your product number is USR8054. It is important that you have your serial
number written down before you install the Wireless Turbo Access Point & Router.
You can find your serial number on the bottom label of the Wireless Turbo Access
Point & Router and on the side of the package. If you ever need to call our Technical
Support department, you will need this number to receive assistance.
Note: Be sure to find out what letter your CD-ROM drives uses before you begin
installing your new product. You will need to know this to properly install your
software.
Connect your modem to the Wireless Turbo
Access Point & Router
Cable or DSL modem users:
• Turn off your computer and turn off or unplug your cable
or DSL modem.
• Attach both antennas to the Wireless Turbo Access
Point & Router.
• Locate the Ethernet cable from your cable or DSL
modem that is connected to your computer’s Ethernet
adapter.
• Disconnect that Ethernet cable from your computer’s
Ethernet adapter, and connect it to the WAN port on
the rear of the Wireless Turbo Access Point & Router.
Note: Some cable or DSL modems can be connected using either a USB cable or
an Ethernet cable. To connect your cable or DSL modem to the Wireless Turbo
Access Point & Router, you must use an Ethernet cable.
Connect your Wireless Turbo Access Point &
Router to your computer and the power supply
To make a wireless connection: Make
sure each wireless card that will be
connected to the network is set to
Infrastructure mode. If necessary, refer to
your Wireless Card manual to determine
how to change this setting.
To make an Ethernet connection: Connect one end of the
supplied Ethernet cable to your computer’s Ethernet
adapter. Connect the other end to one of the LAN ports on
the Wireless Turbo Access Point & Router.
All Users:
Turn on or plug in your cable or DSL modem. Connect the
included power adapter to the power socket on the
Wireless Turbo Access Point & Router. Plug the power
adapter into a standard power outlet. Turn on your
computer.
Configure the basic connection settings
Launch a Web browser. In the location or address line of your Web browser, type
http://192.168.123.254 to access the Web User Interface. The default user name is admin.
There is no default password. Click OK to login.
Perform the steps of the Setup Wizard to configure the basic connection settings of the
Wireless Turbo Access Point & Router. Refer to the “Specialized Internet Connection
Instructions” chapter in the User Guide on the Installation CD-ROM for instructions on
collecting your configuration information.
When you are finished configuring the basic connection settings, you should now have
Internet access. Launch a Web browser and register your product at
www.usr.com/productreg If the page loads, you are finished with the installation
procedure. If the page does not load, refer to the Troubleshooting section.
Note: Refer to the “Configuring the Wireless Turbo Access Point & Router”
section in the User Guide on the Installation CD-ROM for more detailed configu-
ration information. Contact your ISP if you have any questions about your WAN
type or your connection information.
Congratulations! The installation procedure is now complete. You should
now have secure and shared Internet access. If you experience any difficulties,
refer to the Troubleshooting section of this guide or to the User Guide on the
Installation CD-ROM for more detailed information.
If you have any difficulties connecting to the Wireless Turbo Access Point & Router, check the following top
three issues and see if they apply to your situation.
• If you are attempting to create a wireless connection but cannot connect to the Wireless Turbo Access
Point & Router, make sure each wireless card is set to Infrastructure mode. If the wireless cards are set to
802.11g Adhoc mode, you will not be able to connect to the Wireless Turbo Access Point & Router. When
each wireless card is set to Infrastructure mode, it should automatically connect to the Access Point of the
Wireless Turbo Access Point & Router. If the wireless cards do not automatically connect, rescan until they
detect the Wireless Turbo Access Point & Router and connect.
• If you create a wireless connection to the Wireless Turbo Access Point & Router but are experiencing poor
link quality, check the positioning of the Wireless Turbo Access Point & Router. Long distances, multiple
floors, or steel or concrete walls can diminish the link quality. If possible, reposition the Wireless Turbo
Access Point & Router to reduce the effect of any of these obstacles.
• If you have the Wireless Turbo Access Point & Router properly connected and can access the Internet but
are experiencing difficulties connecting with special applications (e.g., ICQ, Battle.net, etc.), you must
assign specific ports in order to bypass the firewall function. For more information about how to configure
this function, refer to the “Special Applications” section within the “Configuring the Wireless Turbo Access
Point & Router” chapter of the User Guide.
Wireless Turbo Access Point & Router
Quick Installation Guide
Package Contents:
-Wireless Turbo Access Point & Router -Quick Installation Guide -5VDC power supply
-two (2) detachable antennas -Installation CD-ROM -one (1) Ethernet cable
Note: For the most updated information, visit: http://www.usr.com/support You
can also refer to the User Guide on the U.S. Robotics Installation CD-ROM for
more detailed information.
Front View
Power LED: This LED is lighted green when the unit is functioning, and blinks when a firmware download is in progress.
This LED is lighted amber during a reboot, a reset, or self-test.
Status LED:This LED is lighted green when wireless functionality is enabled and blinks when there is wireless activity.
WAN LED: This LED is lighted green when a 100mbps device is connected and lighted amber when a 10mbps device is
connected. When traffic is moving through the device, the LED flashes.
LAN 1-4 LEDs: These LEDs are lighted green when a 100mbps device is connected and lighted amber when a 10mbps
device is connected. When traffic is moving through the device, these LEDs flash.
Back View
RESET Button: Press in and hold the RESET button for between five and ten seconds. This will reset the Wireless Turbo
Access Point & Router to the factory default settings.
LAN Ports 1 - 4: The RJ-45 LAN ports are used to connect Ethernet devices to the LAN.
WAN: The RJ-45 WAN port is used to connect the 802.11g Wireless Turbo Router to a broadband modem.
5VDC: This connection port is for the power supply of the Wireless Turbo Access Point & Router.
Antenna Ports: These connection ports are reverse polarity, SMA male connectors.
Wireless Turbo Access
Point & Router
wireless network
card
cable or DSL
modem
rebmuNtcudorPrebmuNlaireS
4508RSU
part number R24.0480.00
Printed in Taiwan