• Home
• Brands
• Dialogic Manuals
• Dialogic DM3 Fax Boards DM/F240-1T1-PCI
• Dialogic DM3 Fax Boards DM/F240-1T1-PCI Quick Installation Manual

Dialogic DM3 Fax Boards DM/F240-1T1-PCI Quick Installation Manual

Download Quick install card of Dialogic DM3 Fax Boards DM/F240-1T1-PCI Network Card for Free or View it Online on All-Guides.com.

1

2

For more information about Linux configuration files, see the

Software Installation Reference.

After the hardware and system software are installed, refer to

the proper configuration files to retrieve the board instance

(ID) number(s) assigned to the board(s) in your system.

1. With your computer on the static-safe work area, switch

off the power and disconnect all power cords from the

electrical outlets.

3. Select an empty PCI expansion bus slot and remove the

slot’s retaining screw and access cover plate (if

applicable).

Dialogic

®

DM3 Fax Boards

Quick Install Card for PCI

• DM/F240-1T1-PCI

• DM/F300-1E1-PCI

Part number 64-0044-02

Copyright © 2002-2007

Dialogic Corporation.

All Rights Reserved.

Before You Begin

Protecting the Board from Damage

Caution! All computer boards are sensitive to

electrostatic discharge (“ESD”). Handle all static-sensitive

boards and components at a static-safe work area, and observe

anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit

http://www.dialogic.com/support/hwinstall to learn more.

Unpacking the Board

Unpack the Dialogic

®

DM3 Fax Board (“board”) according to

the following steps:

1. Prepare a static-safeguarded work area.

2. Carefully remove the board from the shipping

carton and anti-static packaging. Handle the board

by the edges and avoid touching the board’s

components.

3. Lay the board on the static-dissipative work

surface.

Note: Place boards in static-shielding bags when carrying

boards from station to station.

CAUTION: Do not remove the board from the anti-static

packaging until you are ready to install it. Observe proper

anti-static precautions at all times.

Configuring the Hardware

Board Identification

The DM3 device driver, part of the system software, assigns

board instance numbers in ascending order (beginning with 0)

as it detects each board in your system. A board instance

number is the identification (ID) number used by the system

software to recognize the board.

NOTE: If you add or remove a board, the system may

change the existing board instance (ID) numbers.

Windows System

After the hardware and the system software are installed,

refer to the Dialogic

®

Configuration Manager (DCM) utility

to retrieve the board instance (ID) number(s) assigned to the

board(s) in your system.

See the DCM online help for more details about board

identification.

Linux System

In a Linux system, you must set SW1 to a unique number for

each DM3 board in your system. Use a non-magnetic

screwdriver to turn SW1 to 1 of 16 board settings, 0-9 or A-F.

Installing the Hardware

NOTE: You should install the hardware before the system

software. However, if you are adding DM3 hardware to an

existing DM3 system, you do not need to uninstall existing

DM3 software.

2. Remove the computer cover.

Physical Description

1. RJ-48C Jack: Connector to external

digital telephone network interface.

2. General Network Interface Alarm LED

3. Power LED

4. Reset LED

5. SW1: Rotary switch to set board

identification (LINUX systems only).

6. Alarm LEDs: Indicate network alarms for

trunk 1 (CH1).

Red: Indicates loss of signal.

Yellow: Indicates loss of frame

synchronization at far end of external

network.

Green: Indicates signal present; powered

up and receiving signal from external

sources.

Loopback: Indicates loopback mode is

activated.

LEDs also indicate POST status.

7. CT/MVIP Bus Termination Jumpers*:

Bus signal is terminated when the

corresponding jumper clip is installed.

JP2A: CT Bus termination jumper

JP2B: MVIP Bus termination jumper

8. P3: CT Bus connector

9. ISA Edge Retainer

10. Signal Processing Daughterboard

1

5

10

9

8

2

3

4

6

7

JP2B

JP2A

Red

Yellow

Green

Loopback

CH4 CH3 CH2 CH1

*Note: Signal must be terminated only on boards

at each end of the CT Bus cable.