• Home
• Brands
• Dimplex Manuals
• Dimplex DCU18LCD
• Dimplex DCU18LCD Installation And Operating Instructions

Dimplex DCU18LCD Installation And Operating Instructions

Download Installation and operating instructions of Dimplex DCU18LCD Fan for Free or View it Online on All-Guides.com.

1

2

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.

Fan Heaters

Model(s) : DCU18LCD

Installation and Operating Instructions

Dimensions

(millimetres)

08/35058/1 Issue 1

Electrical connection

This heater must be used on an A.C.~ supply only and the voltage

marked on the heater must correspond to the supply voltage. This heater

is fitted with a plug incorporating a 13 amp fuse. When replacing the

fuse, a 13 amp fuse approved by ASTA to BS 1362 must be used.

If the plug is not suitable for the socket outlets in your home, the plug

must be cut off and an appropriate one fitted. A plug cut off from a

mains lead will give a shock hazard if inserted into a 13 amp socket

elsewhere in the house. To avoid this, it should be disposed of

immediately.

NOTE: The fuse cover of a non-rewirable plug must be refitted when

changing the fuse. Should the cover become lost, the plug must not be

used until the correct replacement fuse cover is obtained from your

supplier or by contacting our customer helpline.

IMPORTANT : The wires in this mains lead are coloured in accordance

with the following code :

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead may not correspond with

the coloured markings in your plug, proceed as follows :

Connect the BROWN wire to the terminal marked ‘L’ or coloured RED.

Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK.

Note : ‘L’ or ‘N’ must not be connected to the EARTH terminal marked

‘E’ or or coloured GREEN or GREEN AND YELLOW.

If in doubt, consult your electrician.

Using the Heater

H W D

295 200 155

Model(s) Specification

DCU18LCD 1.8kW Electronic LCD Display

Fig. 1

IMPORTANT SAFETY ADVICE

READ THESE INSTRUCTIONS BEFORE USE.

DO NOT use the heater on deep pile carpets or the long hair

type of rugs, or less than 750mm (30") away from any

overhanging surface. Keep combustible materials such as

drapes and other furnishings clear from the front, sides

and rear of the heater. Do not use heater to dry your laundry.

DO NOT use the heater in the immediate surroundings of a

bath, a shower or a swimming pool.

DO NOT place the heater directly below a fixed socket outlet.

The socket-outlet must be accessible at all times to enable

the mains plug to be disconnected as quickly as possible.

DO NOT COVER or obstruct the air inlet and outlet openings

in any way.

The heater must be on a flat stable surface when in use.

DO NOT operate the heater with the mains lead overhanging

the front outlet grille.

NEVER leave the heater unattended when it is used by or

near the aged, infirm person’s or children.

If you use this heater in conjunction with an external thermal

control, a programme controller, a timer or any other device

which switches on the heater automatically, observe all

safety warnings AT ALL TIMES since a fire risk exists when

the heater is accidentally covered or displaced.

The heater carries the Warning symbol indicating that

it must not be covered.

The instruction leaflet belongs to the appliance and must

be kept in a safe place. If changing owners, the leaflet

must be surrendered to the new owner.

IMPORTANT – If the mains lead of this appliance is damaged,

it must be replaced by the manufacturer or its service

agent or a similarly qualified person in order to avoid a

hazard.

Fig. 2

Operation

When the unit is plugged in and the power switch at the rear of the unit

is switched on a red power light illuminates to indicate that there is

power to the unit. The heater is now in standby mode. The red light will

remain lit until the power switch is switched off or the heater is un-

plugged from the outlet. Pressing the – see Fig. 2, will start the heater

pressing the again will return the heater to standby mode. Upon

turning the heater on, the unit will be in AUTO heat mode and the LCD

displays a set temperature of 35

0

C. The current air temperature will also

appear on the display. At this point the set temperature can be adjusted

as desired using the “+” button or “-“button – see Fig. 2. Pressing the

MODE button selects the heating mode. Pressing the MODE button will

cycle the heater through the heating modes Low heat/High heat/Fan

only/Auto heat. Pressing the MODE button once will set the heater into

LOW heat mode, pressing twice will select High heat, press again to

select Fan only operation. Pressing the MODE button once more will

return the heater to AUTO heat mode. When the heater is in Low heat,

High Heat or Fan only mode the current air temperature will appear on the

display, the SET TEMP indicator will not be displayed. This heater is

provided with an oscillating function. When the OSC button is pressed

the heater will oscillate back and forth. Press it again and the oscillation

will stop.

Note: If switched to standby MODE the heater will retain its last heat

setting. The last heat setting will be cleared from memory once the

power switch at the rear of the heater is switched off or the heater is

unplugged from the outlet.