• Home
• Brands
• Dri-Eaz Manuals
• Dri-Eaz Rebel EX
• Dri-Eaz Vortex Owner 's Manual

Dri-Eaz Vortex Owner 's Manual

Download Owner's manual of Dri-Eaz Rebel EX Dryer for Free or View it Online on All-Guides.com. This version of Dri-Eaz Rebel EX Manual compatible with such list of devices, as: Rebel EX, Sahara, Sahara Pro, Sahara Pro-HP, Vortex

1

2

3

4

Owner’s Manual – Dri-Eaz TurboDryers

230-volt Models

Vortex, Rebel EX, Santana SX, Sahara, Sahara Pro, Sahara Pro-HP

DRI-EAZ PRODUCTS, INC.

15180 Josh Wilson Road, Burlington, WA USA 98233

Fax US: (360) 757-7950 Phone US: (360) 757-7776 Phone UK: (01908) 562611 www.dri-eaz.com

TurboDryers are high-performance airmovers for speed-drying of building structures and contents.

They are designed for a balance of static pressure and airflow, as well as durability and ease of use.

Read And Save These Instructions

Safety Information

Keep Children Away: Do not allow children to play with or

around the unit, which could result in injury. Be sure the unit

is inaccessible to children when not attended.

Keep Unit Grounded: Always operate the unit with a

grounding plug and a grounded electrical outlet. A grounding

plug is an essential safety feature that helps reduce the risk

of shock or fire.

Protect Power Cord from Damage: Never operate a unit

with a damaged power cord, as this may lead to electrical or

fire hazards. If the power supply cord is damaged, it must be

replaced by a cord of the same type and amperage rating.

Extension Cords: Extension cords must be grounded and

able to deliver the appropriate voltage to the unit.

When Using Outdoors: When using outdoors, connect only

to an outlet provided with a Ground Fault Interrupting (GFI)

device, and do not use an extension cord, to reduce the risk

of electrical shock. Do not expose to rain.

Do Not Use Speed Control Device: To reduce the risk of

fire or electric shock, do not use TurboDryers with a solid-

state speed control device.

Handle With Care: Do not drop or throw the unit. Rough

treatment can damage the components or wiring and create

a hazardous condition.

Run on Stable Surface: Always operate the unit on a

stable, level surface, like the floor or a strong counter, so it

cannot fall and cause injury.

Secure During Transport: When transporting in a vehicle,

secure the unit to prevent sliding and possible injury to

vehicle occupants.

Keep Out of Water: Never operate the unit in pooled or

standing water, as this may create a risk of injury from

electrical shock. Do not store or operate outdoors. If elec-

trical wiring or components become wet, thoroughly dry them

Keep Air Intakes Clear: Do not clog or block air intakes, as

may occur if operated to close to draperies or similar

materials. This may cause the unit to overheat and result in a

fire or electrical hazard.

Keep Out Dust and Dirt: Do not allow dust, dirt, or other

particles to be drawn into the air intakes. Dirt in the motor

can cause it to overheat, resulting in a fire or electrical

hazard. If the motor gets dirty, clean it using an air hose.

Allow Repair Only by Qualified Person: Do not attempt to

disassemble or repair the unit if you are not qualified to do

so. You may handle some maintenance and troubleshooting,

but make sure that more complex problems are handled by

an authorized service technician. For information about

authorized repair, call Dri-Eaz at (360) 757-7776.

HOW TO USE TURBODRYERS

TurboDryer airmovers are designed to blow air across wet

surfaces for speed drying. They are especially good for

drying floors because they create a flat ribbon of air. High-

volume airflow will increase the rate of evaporation, help

prevent mould growth, and reduce the risk of additional

moisture damage. Moving air will improve evaporation by re-

moving a boundary layer of saturated air that hangs near wet

surfaces. TurboDryers whisk away this moist air and replace

it with dryer air.

Positioning TurboDryers

When drying in a building, place at least one TurboDryer per

room, or one for every 200 square feet. Place as many as

needed for maximum airflow across all wet areas of the floor.

Ensure that all wet surfaces receive good airflow. Open inter-

ior doors to maintain good air circulation. Doors may need to

be braced to prevent them from blowing shut.

Control the Humidity

Using TurboDryers to speed the rate of evaporation in a

building usually causes the humidity to rise immediately.

When this occurs the air movement becomes less effective