Edelbrock 68832 (Ceramic-Coated) Installation Instructions

Download Installation instructions of Edelbrock 68832 (Ceramic-Coated) Automobile Parts for Free or View it Online on All-Guides.com.

Edelbrock 68832 (Ceramic-Coated) Installation instructions - Page 1
1
Edelbrock 68832 (Ceramic-Coated) Installation instructions - Page 2
2
©2005 Edelbrock Corporation
Catalog #68832 & #68833
Page 1 of 2
Brochure #63-0160
Rev. 9/05
EQUAL LENGTH SHORTY HEADERS
For 1986-1993 Ford Mustang, Mark, Capri with 5.0L V8
Catalog #68832 (Ceramic-Coated)
Catalog #68833 (Ti-Tech Coated)
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new Equal Length Shorty Headers. If you have any questions, please
call our Technical Hotline: 1-800-416-8628, 7am - 5pm, Monday-Friday, Pacific Standard Time or
e-mail us at: [email protected]. Please fill out and mail your warranty card.
DESCRIPTION: These components are designed as a system to improve the exhaust efficiency of the Ford 5.0L V8 engine. A
performance gain can be expected by the installation of the system. This system requires no welding for installation and retains all
O.E.M. emissions equipment.
SUGGESTED TOOLS FOR INSTALLATION: This vehicle has some metric fasteners.
Sockets- 7/16", 1/2", 9/16", 5/8", 11/16" Universal 3/8 drive
Screwdriver- straight blade Ratchet- 1/4" drive
Wrenches- 7/16", 1/2", 9/16", 11/16" Extension- 3-6"
Wire cutters Jackstands, screwdrivers, pliers, crescent wrench,
Pliers hacksaw, etc.
Ratchet- 3/8 drive Liquid penetrant, (GM #1052627) anti-seize
Extension- about 10" compound (GM #5613695)
SPECIAL NOTICE: This Edelbrock part has received an Executive Order number (E.O.) from the California Air Resources Board
(C.A.R.B.) making it legal for street use on pollution-controlled motor vehicles in all 50 states. To assist you with emissions equipment
certification, we have included a silver fan shroud decal to verify that this part is a legal replacement part on the vehicle for which it
is cataloged. The adhesive-backed decal should be affixed to your fan shroud next to the existing emission and engine specification
decal. Do not cover your original equipment specification decal with the Edelbrock fan shroud decal.
WARNING: The use of “Thermal Wrap” or any aftermarket coating process will void the warranty on your headers. Those products
can cause excessive heat and moisture buildup resulting in corrosion and early failure of the system.
CAUTION: Due to higher underhood temperatures generated by headers, vehicles equipped with original spark plug wires should
have them replaced with high temperature plug wires for longer life.
DISASSEMBLY
1. Raise front of vehicle using the front crossmember to
support the vehicle. Position jackstands under the
crossmember. Drive up ramps may also be used to raise
the front of the vehicle. Make sure parking brake is on and
the rear wheels are blocked so vehicle cannot roll.
2. Loosen H-pipe from stock exhaust headers.
3. Remove the dipstick tube assembly, and clutch cable
bracket from the left side of the engine.
4. Remove air intake tube, air cleaner cover and air flow
sensor from the right side of the engine. Also remove the
smog hoses from the same side.
5. Remove the stock exhaust headers and gaskets. Make
sure the gasket surfaces are clean.
INSTALLATION INSTRUCTIONS
6. Take all the spark plugs out, remove plug wire holders
from bolt posts on the valve covers. Label all plug wires
for ease of re-assembly.
LEFT SIDE INSTALLATION
1. Put left side header into position. Jostle H-pipe to allow
header to drop into place. Set H-pipe in place do not
tighten.
2. Install supplied exhaust gasket in place between header
and cylinder head. Install one bolt to hold gasket in place.
3. Install supplied header bolts. Tighten all bolts evenly.
4. Re-install clutch cable bracket, spark plugs, plug wires,
and dipstick tube assembly. Do not tighten H-pipe.