Edelbrock 7129 Installation Instructions

Download Installation instructions of Edelbrock 7129 Automobile Parts for Free or View it Online on All-Guides.com.

Brand: Edelbrock

Category: Automobile Parts

Type: Installation instructions

Model: Edelbrock 7129 , Edelbrock 7183

Pages: 2 (0.1 Mb)

Download Edelbrock 7129 Installation instructions

Edelbrock 7129 Installation instructions - Page 1
1
Edelbrock 7129 Installation instructions - Page 2
2
Catalog #7129, #7183
Rev. 1/08 - AJ/mc
©2008 Edelbrock Corporation
Brochure #63-7129Page 1 of 2
PERFORMER RPM E-BOSS INTAKE MANIFOLDS
For 302 & 351 c.i.d. Ford Windsor Engines
Catalog #7129 & #7183
INSTALLATION INSTRUCTIONS
®
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,
it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical Hotline at:
1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at [email protected]
.
IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation
will void your warranty and may result in poor performance and engine or vehicle damage.
DESCRIPTION: The Edelbrock Performer RPM E-Boss intake manifolds are designed to allow the use of our high performance Cleveland-style cylinder
heads on Windsor blocks with a deck height of 8.2”(302 only) or 9.5” (351W). Port exits are matched to our #61689 cylinder heads. These manifolds
will optimize power from 1,500 to 6,500 rpm and should be matched with other engine components designed for the same operating range.
ACCESSORIES & INSTALLATION ITEMS: Major recommendations are listed below. See our catalog for details. To order a catalog, call (800)
FUN-TEAM, or visit www
.edelbrock.com.
EGR SYSTEMS: Intake manifold will not accept stock EGR (Exhaust Gas Recirculation) equipment. EGR systems are used on most 1972 and later
model vehicles. Check local laws for requirements.
CARBURETOR RECOMMENDATIONS: Engine displacement, vehicle weight, and intended driving style will significantly impact your carburetor
selection. For a typical muscle car that will be driven aggressively (but not competively) a 650 cfm carburetor such as our Thunder AVS #1805 or
#1806 will be sufficient. Engines that have been stroked larger than 360 c.i.d. and/or will be driven on the track regularly may want to use an
800 cfm carburetor such as our Thunder AVS #1812 or #1813 for peak performance.
THROTTLE BRACKETS: The throttle and kickdown bracket on some vehicles may require modification to fit. C4 and C6 transmissions will require
the use of kickdown adapter #1481, while an AOD transmission will require an SRK-4000 adapter from Lokar. When using Edelbrock carburetors
on a 302, use #1490 or #1845 throttle plate kit to line up the stock throttle bracket to the Edelbrock carburetor throttle lever. 351W engines will
use throttle bracket relocation plate #1491 or #1846.
GASKETS: We recommend Fel-Pro intake gasket #1021 be used with the #7129 and #7183 manifolds. Do not use competition-style intake
gaskets for these street manifolds. Due to material deterioration over time, internal leakage of vacuum, oil, and coolant may occur.
CLEVOR/BOSS 302 CLONE COMPONENTS: Several components will be needed to adapt a Windsor engine block to Cleveland cylinder heads.
PISTONS: Aftermarket pistons that have been notched for the valve angle of a Cleveland head will be necessary. These can be purchased from
companies such as JE, Ross, CP, and Probe.
VALVETRAIN: Most street applications will want to use a rocker ratio of 1.73:1. A full set of rocker arms can be purchased from Crane as part
#27750-16. These will use 8.550” pushrods if matched with OE Ford hydraulic roller lifters. If you are using a cylinder head equipped with guide
plates, such as Edelbrock heads #61689, be sure to only purchase hardened steel or chromoly pushrods.
MOUNTING HARDWARE: These manifolds require a total of sixteen (16) intake manifold bolts to be properly secured. You will need eight (8)
bolts that are 3/8”-16 and 1-3/4” long, and eight (8) bolts that are 5/16”-16 and 2” long. All sixteen (16) bolts will require chamfered hardened
steel washers between the manifold and the head of the bolt. The longer bolts will thread through the vertical bosses, while the shorter bolts will
mount perpendicular to the flange. See Figure 1 for the proper torque sequence.
CAMSHAFT AND HEADERS: Performer RPM Series manifolds are compatible with aftermarket camshafts and headers designed to work in the
1500-6500 rpm range. Header primary tube diameter should be 1-3/4".