Edge DiskGO! 196332-PE Installation Manual

Download Installation manual of Edge DiskGO! 196332-PE Storage for Free or View it Online on All-Guides.com.

Edge DiskGO! 196332-PE Installation manual - Page 1
1
This Product is backed by a One Year Limited Warranty.
For complete warranty information visit www.edgetechcorp.com/register
NEED
HELP?
TECH SUPPORT
www.edgetechcorp.com/support
3210 Ver3(09-04)
DiskGO!
TM
2.5” Ultra Portable Hard Drive
Installation Guide
327 East 14th Street / Ada OK 74820 (800) 332-6581 / (580) 332-6581 / www.edgetechcorp.com
EDGE
TM
and DiskGO!
TM
are trademarks of EDGE Tech Corp. Trademarked words or logos used herein are property of their respective owners.
IMPORTANT
PLEASE CONTACT A QUALIFIED TECHNICIAN FOR ASSISTANCE IN INSTALLING OR USING THIS PRODUCT IF YOU ARE NOT
FAMILIAR WITH DOING SO. ANY INSTRUCTIONS INCLUDED WITH THE PRODUCT ARE FOR CONVENIENCE ONLY AND ARE NOT
INTENDED TO BE ALL-INCLUSIVE.
Software drivers are required only for Windows 98SE.
Windows ME, Windows 2000, Windows XP and MacOS 9.x+ do
not require drivers.
If you are using Windows 98SE, download the drivers and
install BEFORE you connect the drive unit.
1. Download the driver from www.edgetechcorp.com/support
and save it to a folder of your choice (note: remember where
you saved the file).
2. Extract (UnZIP) the driver files to a new folder on your
desktop.
3. Plug the DiskGO! Ultra Portable Hard Drive into the USB
port. Windows 98 should detect it automatically.
4. The “Add New Hardware Wizard” will appear. Please follow
the instructions below to continue:
a. Click the “Next” button
b. Check “Search for the best driver for your device
(“Recommended”) and click the “Next” button.
c. Specify the location where you saved the driver file (from
Step 2, above) and click “Next”.
d. The window will show the name of the USB device. Click
on the “Next” button to install the driver.
e. After installing the driver, click the “Finish” button to
complete the driver installation.
f. Restart your computer.
NOTE: More detailed file format information exists on our
website (www.edgetechcorp.com/support).
Once you have set-up your DiskGO! Ultra Portable Hard Drive,
you can reformat or partition it to suit your needs.
USB and FireWire external devices feature hot swappable “plug
& play” connections. This means that your drive can be
connected and disconnected while the computer is running.
However, to prevent failures, it is important that you follow
these steps when disconnecting any USB or FireWire peripheral
device.
Mac Users
You must unmount or ‘eject’ the drive unit before disconnecting
it or switching off the power. To do this, drag the DISKGO hard
drive icon to the trash. The drive cables can now be
disconnected and/or the power switched off.
PC Users (Windows 98SE and Windows XP)
Simply disconnect the drive when it is not active (the R/W
activity lights are not blinking). No other steps are required.
Windows 2000, Windows ME
Unmount or ‘eject’ the drive unit before disconnecting it or
switching off the power.
1. When you connect an external device, an “Eject” icon will
appear in the System Tray. The Eject icon is a small green arrow
over a hardware image. The System Tray is located near the
clock in the lower right-hand side of your screen. Double-click
the “Eject” icon.
2. The “Safely Remove Hardware” dialog box will appear, listing
the devices that the “Eject” icon controls (all external devices).
Highlight the unit you wish to unmount and click the “Stop”
button.
3. Next, the “Stop a Hardware Device” dialog box will appear,
listing the device controllers assigned to that device. Highlight
the top listing and click the “OK” button.
4. You will then be given the following message, “Safe to Remove
Hardware” (or similar). It is now safe to disconnect the device.
1. Connect the USB cable to the mini USB port on back of
the drive unit.
2. Connect one or both USB plugs to the computer to obtain
sufficient power (the USB port supplies power to the drive
unit.) Most combinations will operate normally with only
one of the USB plugs connected to the computer. Some
machines require both.
3. Your DiskGO! Ultra Portable Hard Drive should appear
as an external drive in “My Computer” and in “Windows
Explorer”. The drive icon should appear with the volume
name “DISKGO” (or similar) in MacOS and Windows.
Windows should automatically assign a drive letter.
4. Once your drive appears in “My Computer”, “Windows
Explorer” or on your MacOS desktop, you can then use it to
read and write files in the same way that you use your
computer’s internal hard drive.
IMPORTANT INFORMATION!
The DiskGO! Portable Hard Drive is pre-formatted
for the PC in FAT32. If you plan on sharing the hard drive
between a Mac and a PC, you will need to leave the drive
formatted as FAT, FAT16, or FAT32. This will allow the drive
to be usable on either platform and data shared between the
two. MacOS cannot read the NTFS file system.
MacOS X v10.2 through 10.2.8 cannot mount a
FAT32 partition larger than 137GB (128GB binary value).
Since your external drive comes with a large FAT32 partition
preinsalled, you must initialize the drive to use it in MacOS X
v10.2 through 10.2.8. See this Apple KnowledgeBase
File System Formats
document for more information:http://docs.info.apple.com/
article.html?artnum=107483
If you intend to use your external hard drive only in MacOS
you must initialize the entire volume with MacOS Extended (Warning:
ALL DATA WILL BE LOST. Back up all data.) If you intend to use
your device with both a PC and Mac, create partitions on the drive
of 128GBor less,and initialize each partition with MS-DOS (Warning:
ALL DATA WILL BE LOST. Back up all data.)
MAC USERS: After connecting your DiskGO!
USB or FireWire Drive, it may take 1-2 minutes or
more for the drive icon to appear on your desktop.
DO NOT shut down or disconnect your hard drive
during this load!
Hardware Installation
Software Installation
Disconnecting Your Drive