ALCATEL Mobile Phones T25-CE User Manual
Download Operation & user’s manual of Alcatel T25-CE Telephone for Free or View it Online on All-Guides.com.
Brand: Alcatel
Category: Telephone
Type: Operation & user’s manual for Alcatel T25-CE
Pages: 2 (1.63 Mb)
1
2
Alcatel Logo and Alcatel name are trademarks of Alcatel and used under
license by Thomson.
T25-CE
T25-CE
TROUBLESHOOTING TIPS
PROBLEM SOLUTION
No dial tone
Can’t dial out
•
Check hook switch to make sure it pops up.
•
Make sure TONE/PULSE is set to correct position.
•
Unplug the phone, wait 30 seconds, and plug
the phone back in.
Phone doesn’t
ring
•
Check phone line cord.
•
Could have too many phones on one line. (The total
REN of all phones should not be greater than the
maximum REN for your area, Usually 5.)
CARE AND MAINTENANCE
To keep your phone working and looking good, please follow these
guidelines:
• Avoid putting near heating appliances and devices that generate
electrical noise (for example, motors and uorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping and other rough treatment of the unit.
• Never use a strong cleaning agent or abrasive powder because
this will damage the nish.
• Retain the original package in case you need to return is at a later
date.
Used equipment must be disposed of in compliance
with current environmental protection regulations.
You should return it to your reseller or dispose of it in an
approved recycling centre.
INTRODUCTION
Your telephone is designed to give you exibility in use, and high
quality performance. To get the most from your new telephone, we
suggest that you take a few minutes right now to read through this
User’s Tips.
If you have any questions or problems, consult the Troubleshooting
Tips for the solution.
PARTS CHECKLIST
Your package should contain the following items:
Base Handset Coiled cord Line cord
INSTALLATION AND SETUP
You GE telephone can be mounted on the wall or placed on a
table. After you decide which type of installation you want, refer to
the appropriate installation diagram.
BEFORE YOU BEGIN
MODULAR JACK REQUIREMENTS
You need a RJ11C type modular jack, which is the most
common type of phone jack and might look like one
pictured here. If you don’t have a modular jack, call your
local phone company to nd out how to get one installed.
Modular telephone line jack
DESKTOP INSTALLATION
1. Adjust the RINGER volume switch to the desired setting. Default
setting is HI.
2. Set the PULSE/TONE switch to TONE if you use Touch-Tone Service;
Set it to PULSE if you have rotary service. Default setting is TONE.
3. Set the Flash time switch (600ms, 300ms, 100ms) to the appropriate
setting.
Default setting is 600ms.
4. Plug the handset cord into the handset, and into the telephone
jack on the left side of the unit.
5. Plug the telephone line cord into a modular jack (RJ11C) and into
the LINE jack on the back of the unit.
6. Place the handset to base cradle.
WALL MOUNT INSTALLATION
The telephone can be mounted on a wall phone plate (not included).
1. Adjust the wall mount knob on cradle of base of apply to wall
mount.
2. Set the RINGER VOLUME switch to the desired setting. Default
setting is HI.
3. Set the PULSE/TONE switch to TONE if you use Touch-Tone service:
set it to PULSE if you have rotary service. Default setting is TONE.
4. Set the Flash time switch (600ms,300ms,100ms) to the appropriate
setting. Default setting is 600ms.
5. Adjust the wall hook on cradle of base to apply to wall mount.
6. Plug the phone cord into the phone jack on the back of the unit.
7. Connect the phone cord to the modular jack on the wall.
8. Place the base to the wall mount plate.
9. Plug the handset cord into the handset and into the unit, and then
hang up the phone.
Use/Ring indicator
USING FEATURES
MAKING A CALL
1. Lift the handset and wait for a dial tone.
2. Dial the telephone number using the keypad.
RECEIVING A CALL
Lift the handset to answer the call.
RINGER VOLUME CONTROL
Use the RINGER volume switch on the back of the base to adjust the
volume of the ringer.
FLASH BUTTON
Press the FLASH button instead of using the hook switch to activate
customer calling services such as call waiting or call transfer, which
are provided by your local phone company.
REDIAL BUTTON
Redial the last number you called by pressing the REDIAL button after
you get a dial tone. Maximum digits of redial is 32.
Wall plate
9
180℃
Flash button Redial button
“WEEE” Weight: 0.452Kg
DOC