Wilbur Curtis Company PC-4D System Instructions
Download System instructions of Wilbur Curtis Company HC-1D Coffee Maker for Free or View it Online on All-Guides.com. This version of Wilbur Curtis Company HC-1D Manual compatible with such list of devices, as: HC-1D, PC-1D, PC-2D, PC-3D, PC-4D
Brand: Wilbur Curtis Company
Category: Coffee Maker
Type: System instructions
Model: Wilbur Curtis Company HC-1D , Wilbur Curtis Company PC-1D , Wilbur Curtis Company PC-2D , Wilbur Curtis Company PC-3D , Wilbur Curtis Company PC-4D
Pages: 4 (0.6 Mb)
1
Primo Cappuccino System Instructions
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO WWW.WILBURCURTIS.COM
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an autho-
rized Wilbur Curtis service center.
• Do NOT immerse the unit in water or any other liquid
• To reduce the risk of fire or electric shock, do NOT open top panel. No user serviceable parts inside. Repair should be
done only by authorized service personnel.
•
Keep hands and other items away from hot parts of unit during operation.
• Never clean with scouring powders or harsh implements.
Conventions
WARNINGS – To help avoid personal injury
Important Notes/Cautions – from the factory
Sanitation Requirements
Your Curtis ADS System is Factory Pre-Set and Ready to Go… Right from the Carton.
Following are the Factory Settings for your ALPHA™ DS Coffee Brewing Systems:
• Tank Temperature = 190°F
• Flavor Controls= Set at 100%
• Dispensing Mode Set for Manual Dispensing
Generally there will never be a reason to change your ADS programming. However, should you need to make slight adjustments to meet
your brewing needs, programming instructions are provided later in this manual.
System Requirements:
• Water Source 20 – 90 PSI (Minimum Flow Rate of 1 GPM)
• Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for your model.
Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having jurisdiction.
SETUP STEPS
The unit should be level (left to right and front to back), located on a solid counter top. Connect a water line from the water filter to the
brewer. NOTE: Some type of water filtration device must be used to maintain a trouble-free operation. (In areas with extremely hard
water, we suggest that a sedimentary and taste & odor filter be installed.) This will prolong the life of your brewing system and enhance
coffee quality.
1. Connect a water line from your facility to the 1/4” flare water inlet fitting of the valve, behind the machine. Water volume
going to the machine should be stable. Use tubing sized sufficiently to provide a minimum flow rate of one gallon per minute.
2. Plug the power cord into an electrical outlet rated at 20A.
3. Switch on the CONTROL switch that runs power to the components in the machine. The lights (display window & row of
buttons) on the front door will activate and the heating tank will start to fill.
4. Once the water level has risen and covered the heating element, turn on the power to the heating element at the HEATING
ELEMENT switch behind the unit.
5. Water in the heating tank will require about 30 minutes to reach operating temperature (factory setting of 190°F). At this
time the READY light will come on.
6. Remove and fill the canisters with powdered cappuccino mixes.
The National Sanitation Foundation requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for
cleaning underneath.
2. In some areas an approved backflow prevention device may be required between the brewer and the water supply.
OPERATION INSTRUCTIONS
1. Choose a flavor. Place your cup under the spout beneath the desired flavor.
2. Push the dispensing button for this flavor.
3. Allow the Primo Cappuccino unit time to completely dispense the product.
WILBUR CURTIS COMPANY, INC.
FILL CANISTERS DAILY
1. Open the front door to access canisters.
2. The canisters must be removed from the unit for filling. The rectangular canisters hold approximately four pounds of product. Each
round cannister will hold approximately six pounds of product.
3. Reposition the canisters on the machine, aligning the gear socket with the motor shaft. The pin under the canister must align with
the guide hole on the support shelf.
Important Safeguards/Conventions
CAUTION: DO NOT
connect this unit to hot
water. The inlet valve is
not rated for hot water.
CAUTION: Please use
this setup procedure
before attempting to use
this appliance. Failure to follow the
instructions can result in injury or the
voiding of the warranty.
WILBUR CURTIS COMPANY
Montebello, CA 90640
ISO 9001 REGISTERED
C
WARNING HOT LIQUID,
Scalding may occur.
Avoid splashing.
Models Included
PC-4D
PC-3D
PC-2D
PC-1D
HC-1D
FIND OUT MORE
ON THE WEB.
WILBURCURTIS.COM
FIND OUT MORE
ON THE WEB.
WILBURCURTIS.COM
WARNING, HOT
LIQUID