Epson WorkForce 600 Start Here Manual

Download Start here manual of Epson WorkForce 600 Series Adapter, All in One Printer for Free or View it Online on All-Guides.com.

Epson WorkForce 600 Series Start here manual - Page 1
1
Epson WorkForce 600 Series Start here manual - Page 2
2
Epson WorkForce 600 Series Start here manual - Page 3
3
Epson WorkForce 600 Series Start here manual - Page 4
4
Epson WorkForce 600 Series Start here manual - Page 5
5
Epson WorkForce 600 Series Start here manual - Page 6
6
Epson WorkForce 600 Series Start here manual - Page 7
7
Epson WorkForce 600 Series Start here manual - Page 8
8
*411556300*
*411556300*
Canada only: For French speakers, remove sticker(s) from the backing sheet and
place over corresponding text on the control panel.
Caution: Do not open ink cartridge packages until you are ready to install the ink.
Cartridges are vacuum packed to maintain reliability.
If anything is missing, contact Epson as described on the back
under “Any questions?”.
Remove all protective materials.
Unpack
1
Start Here
Make settings
3
1 Select your language.
Press or to select the
desired option.
Press OK when done.
2 Select your country/region, then press OK.
3 For the Daylight Saving Time setting, select Summer if your region uses
Daylight Saving Time and it’s currently in effect. (DST is effective from
spring through summer.) Otherwise, select Winter to turn off the setting.
Press OK.
4 Press or to select the date format,
then press . Don’t press OK yet.
5 Use the numeric keypad to set the date. Don’t press OK yet.
6 Press or to select the time format,
then press . Don’t press OK yet.
7 Use the numeric keypad to set the time.
8 If you selected 12h as the time format, press or to
select AM or PM.
9 Press OK when done.
Note: You can change the date and time settings by pressing the Home button,
selecting Setup, selecting Printer Setup, then selecting Date/Time.
1 Open the paper support and pull out the extension.
2 Extend the output tray and raise the stopper.
Note: If you are using legal-size paper, do not raise the stopper.
3 Flip the feeder guard forward, then squeeze the edge guide and slide it to
the left.
4 Load paper against the right edge guide and behind the tab, with the
printable side face up.
Note: Don’t load the paper sideways; always load it
short edge first.
5 Slide the edge guide over, then flip the feeder guard back.
5
Load paper
Install ink cartridges
4
Note: Don’t load paper before installing the ink cartridges.
1 Lift up the scanner.
2 Open the cartridge cover.
3 Shake the ink cartridges
gently 4 or 5 times, then
unpack them.
4 Remove only the yellow tape from each cartridge.
Caution: Don’t remove any other seals from the cartridges.
5 Insert the cartridges in the
holder for each color.
6 Press the cartridges down until they click.
7 Close the ink cartridge cover and press it
down until it clicks.
8 Close the scanner.
9 Press the OK button to charge ink. Charging takes about 2 minutes.
Note: Your WorkForce 600 Series ships with full cartridges and part of the
ink from the first cartridges is used for priming the WorkForce 600 Series.
Caution: Don’t turn off the WorkForce 600 Series while the ink system is
initializing or you’ll waste ink.
(Included for
Canada only)
1 Connect the power cable.
Caution: Do not connect to your computer yet.
2 Lift the control panel to raise it, then press the On button.
Turn on
2
Series
Ethernet cable
(gray)
Phone cord
(black)
Power cord