Tech 21 Midi Moose Owner's Manual
Download Owner's manual of Tech 21 Midi Moose Electronic Keyboard for Free or View it Online on All-Guides.com.
Brand: Tech 21
Category: Electronic Keyboard
Type: Owner's manual for Tech 21 Midi Moose
Pages: 2 (0.19 Mb)
1
2
MIDI CHANNELS
In order to communicate program change information, the MIDI Moose and the receiving MIDI
unit(s) must be on the same channel.You need not change the MIDI Moose channel if your receiv-
ing unit is on OMNI. (OMNI mode receives MIDI program change information on any of the 16
selectable MIDI channels.)
The MIDI Moose is factory set at Channel 1. When you initially power up,“1c” will flash in
the numerical display for a few seconds. If you want to change the MIDI channel on certain occa-
sions but not save the change, hit the UP or DOWN footswitch accordingly while the channel setting is flash-
ing.The MIDI Moose will then operate on the new channel until you disconnect and reboot.If the channel set-
ting stops flashing before you have a chance to change it, disconnect the power source for at least 10 seconds.
Reconnect the power source and continue as above. NOTE: the MIDI Moose will revert back to the last saved
channel each time you power up.
To change and save a different MIDI channel setting:
1. Depress the UP and DOWN footswitches simultaneously.The current MIDI channel number will
flash (1c).
2. Use the UP or DOWN footswitch accordingly to get to the desired channel.
3. Depress the 1/6 footswitch to save the newly selected MIDI channel.When saved, the
numerical display will stop flashing. After a few seconds, the MIDI Moose will display the last
program number you were in.
If you have two or more MIDI controlled processors linked together, be sure they and the MIDI
Moose are all on the same channel. If you do not want a particular processor in the chain to
accept program change information from the MIDI Moose, be sure to change that unit’s channel.
PHANTOM POWER OPERATION VIA MIDI CABLE
The MIDI Moose will accept power via a standard 5 conductor/
pin MIDI cable through Pins 1 and 3. Consult the owner’s manual
of your processor for its phantom power support capabilities
and specifications.
NOTE: Power must be between 8 and 15V DC, any polarity.
POWER REQUIREMENTS
• Phantom power operable via MIDI cable. (See above.)
• Utilizes standard 9V alkaline battery (not included).To install, simply remove door cover.
NOTE: When battery nears depletion,“Lo” will appear in the numerical display.
Power consumption of numerical display: approx. 15mA.
• USE DC VOLTAGE POWER SUPPLY ONLY! Failure to do so may damage the unit and
void warranty. DC Power Supply Specifications:
.
9V DC regulated or unregulated, 100mA minimum;
.
2.1mm female plug, center negative (-).
Optional factory power supply is available:Tech 21 Model
#
DC2.
WARNINGS:
• Attempting to repair unit is not recommended and may void warranty.
• Missing or altered serial numbers automatically void warranty. For your own protection, be sure
serial number labels on the unit’s back plate and exterior box are intact, and return your
warranty registration card.
ONE YEAR LIMITED WARRANTY. PROOF OF PURCHASE REQUIRED. Manufacturer
warrants unit to be free from defects in materials and workmanship for one (1) year from date of
purchase to the original purchaser and is not transferable.This warranty does not include damage
resulting from accident, misuse, abuse, alteration, or incorrect current or voltage. If unit becomes
defective within warranty period,Tech 21 will repair or replace it free of charge.After expiration,
Tech 21 will repair defective unit for a fee.
ALL REPAIRS for residents of U.S. and Canada: Call Tech 21 for Return Authorization
Number. Manufacturer will not accept packages without prior authorization, pre-paid freight
(UPS preferred) and proper insurance.
FOR PERSONAL ASSISTANCE & SERVICE:
Contact Tech 21 weekdays from 9:00 AM to 5:00 PM, EST.
MADE IN THE U.S.A.
Tel: 973-777-6996 / Fax: 973-777-9899
www.tech21nyc.com / info@tech21nyc.com
©2006 Tech 21 USA, Inc.
3
1
Owner’s Manual