• Home
• Brands
• Techko Manuals
• Techko S082K
• Techko S082K Operation Manual

Techko S082K Operation Manual

Download Operation manual of Techko S082K Security System for Free or View it Online on All-Guides.com.

1

2

SAFETY SECURITY

MAGNET GUARD

MODEL S082X/S082K

S082X

S082K

OPERATION MANUL

3.INSTANT mode.

When an entry is detected. The alarm sounds

immediately. This is used to protect you when you

are at home.

4.DELAY mode.

This mode is used when you are leaving your home.

On your return, an entry alert beep tone will sound

to alert you to disarm the unit. If the unit is not

disarmed within10 seconds of entry, the alarm will

sound a110db (S082KA is 115db) alarm siren.

5.The 110db/115db alarm will sound for about 30/36

seconds, while the alarm is sounding or during the

entry alert time the security code can be entered to

disarm the unit.

6.To disarm the unit, enter the security code followed by

the #ON/OFF button.

CHIME MODE

1.Before activating the chime, slide the function switch

to the CHIME position.

2.Enter the security code followed by the #ON/OFF button.

3.The ARM LED will illuminate to verify the unit is ON,

followed by a short beep. If the ARM light does not

illuminate this indicated the unit is OFF.

4.The chime will sound if there is an entry. The chime will

sound for each entry until the unit is turned OFF(disarmed)

NOTE: The position of the function switch does not

necessarily indicate the mode the unit is in

(CHIME / INSTANT / DELAY). Each time before

activating the unit, set the function switch to the correct

position for the mode desired.

PANIC ALARM

The red PANIC button on the front panel activates the

alarm during a possible emergency.

1.Press the panic button. This will activate the 110db

(S082KA is 115db) alarm siren.

2.Disarm the PANIC alarm, follow the same procedure as

you would to DISARM the unit.

CAUTION

THE MAGNET GUARD IS EXTREMELY LOUD. FOR YOUR

SAFETY. NEVER PLACE THE UNIT CLOSE TO YOUR EARS.

TO TEST THE ALARM, DIRECT THE UNIT AWAY FROM YOU

AT ARMS LENGTH AND ACTIVATE.

PATENT PENDING NOTICE

THIS PRODUCT IS PROTECTED UNDER FEDERAL PATENT. TRADEMARK AND COPYRIGHT

LAWS AND LAWS PREVENTING UNFAIR COMPETITION. NO DUPLICATION OR SIMULATION OF

THIS PRODUCT IS PERMITTED EXCEPT BY WRITTEN AUTHORIZATION OF TECHKO, INC.

TECHKO AND THE CONFIGURATION OF THIS PRODUCT ARE TRADEMARKS OF TECHKO, INC.

COPYRIGHT 1992 TECHKO, INC. ALL RIGHTS RESERVED

ALARM OUTPUT AND PANIC BUTTON TEST

To test the alarm output, press the PANIC button located on

front of the unit. (THIS UNIT IS VERY LOUD, COVER THE

SIREN ON THE FRONT OF THE UNIT BEFORE ACTIVATING).

The unit will immediately sound a piercing alarm siren. To

disarm the unit, enter your security code followed by the

#ON/OFF button. (If you have not entered a security code

the default is 0 and S082K is 5

CHIME TESTING

1.Set the function switch to the CHIME position.

2.Enter the security code followed by the #ON/OFF button,

the ALARM LED will illuminate. If this does not happen

repeat steps 1 and 2.

3.Close the door and then open it again, a pleasant chime will

sound 3 times.

4.To disarm the unit, enter the security code followed by the

#ON/OFF button.

5.As long as the unit is in the ARM mode, the chime will

continue to sound until DISARMED .

ALARM TESTING

1.Set the function switch to the INSTANT or DELAY

position.

2. Enter the security code followed by the #ON/OFF button,

the ARM LED will turn on. If this does not happen, repeat

steps 1 and 2.

3. Close the door and open it again in INSTANT mode, the

alarm sounds immediately. If the alarm is in DELAY mode,

the alarm will emit a low beep tone to alert your to disarm the

unit, if not disarmed, the unit will then sound a piercing alarm.

4.To disarm the unit, enter the security code followed by the

#ON/OFF button.

Note: in both modes, CHIME or ALARM (instant / delay) the unit will continue to

sound until DISARMED . The unit will only sound the ALARM if ARMED in

the ALARM mode. If armed in the CHIME mode the unit will sound only the CHIME.

If function switch is changed after the unit has been activated, this will not alter the

sound being produced.

ALARM MODE

1.Before arming the unit slide the function switch to the

INSTANT/DELAY position.

2.To arm the S082X / S082K, enter the security code

followed by the #ON/OFF button, the ARM LED will

turn on. If this does not happen repeat steps 1 and 2.

TESTING

OPERATION

1

2

3

4

5

6

7

8

9

*

0

#

S082KA

1

2

3

4

5

*

#

PANIC

S082X

TEMPLATE

SCREW HOLE

SCREW HOLE

MODE S082KA

SCREW HOLE

Customer Service :

1-888-8TECHKO (1-888-883-2456)

Website: www.techkomaid.com

Mfg. By

9767 Research Drive

Irvine, CA 92618-4626

MADE IN CHINA