Home | About | Contact

Extron electronics XTRA FULL RACK XPA 2002 User Manual

Download Setup manual of Extron electronics XTRA FULL RACK XPA 2002 Amplifier, Home Theater System for Free or View it Online on All-Guides.com. This version of Extron electronics XTRA FULL RACK XPA 2002 Manual compatible with such list of devices, as: XTRA FULL RACK XPA 2002, XTRA FULL RACK XPA 2002-70V, XTRA FULL RACK XPA 2003C-70V, XTRA FULL RACK XPA 2004

Extron electronics XTRA FULL RACK XPA 2002 Setup manual - Page 1
1
Extron electronics XTRA FULL RACK XPA 2002 Setup manual - Page 2
2
Page 1
background image

XTRA™ Full Rack Series • Setup Guide

This guide provides basic instructions for an experienced installer  
to set up and operate the Extron

®

 XTRA Full Rack Series of 

power amplifiers.  All references refer to the  
XTRA Full Rack Series: XPA 2002, XPA 2002-70V, 2003C-70V,  
and 2004 User Guide
.

• 

XPA 2002 outputs stereo audio at 200 watts rms per channel (4-ohm speakers) or  
100 watts rms per channel (8-ohm speakers) on channels 1 and 2.  Output is 400 watts 
bridged mono (8-ohm speaker).

• 

XPA 2002-70V outputs 200 watts rms per channel on channels 1 and 2 for 70 V systems.

• 

XPA 2003C-70V outputs 200 watts per channel (4-ohm speakers) or 100 watts per channel 
(8-ohm speakers) on channels 1 and 2, and 200 watts (70 V line, mono) on channel 3.

• 

XPA 2004 outputs stereo audio at 200 watts per channel (4-ohm speakers) or 100 watts 
per channel (8-ohm speakers) on channels 1, 2, 3, and 4. Output is 400 watts per bridge 
in bridged mono (8-ohm speakers) on bridge A (channels 1 and 2) and bridge B (channels 
3 and 4).

Installation

NOTE:  Adjust the audio level to = prior to the amplifier being powered back up in step 5

See “Rear Panel Features and Operation” in the user guide.

1. 

Turn off all equipment including the XPA amplifier by toggling the power off and 
disconnecting the power cords.  Verify that the amplifier is disconnected from the 
power source before proceeding.

2. 

Mount the amplifier — For diagrams of typical application examples, see “Application 
Examples” in the user guide. For further mounting instructions, see “Mounting the XTRA 
Series of Power Amplifiers” in the user guide. 
  

3. 

Wire input to the 3.5 mm input connectors of the amplifier, as shown in the following 
illustration. See “Rear Panel Features and Operation” in the user guide for bridging 
information. 

" (5 mm) MAX.

Tip

Sleeve

Ring

Tip

Sleeve

Unbalanced Input 

Balanced Input 

   The wires must not be tinned: tinned wire does not 

      hold tight in the captive screws and can break easily 

      after several bends.

4. 

Wire the outputs — Wire speakers to the output connectors of the amplifier using the 
included 2-pole (XPA 2002, XPA 2002-70V and XPA 2003C-70V) or 4-pole  
(XPA 2003C-70V and XPA 2004) screw lock plug. 
  
2-pole (70 V) output connector wiring: 
 
 
 
 
 
4-pole (8 ohm or 4 ohm) output connector wiring: 
 
 
 
 
 
 
 

IMPOR

TANT

:

Refer to www

.extron.com for 

the complete user guide and 

installation instructions.

1

2

3

(BRIDGE A)

(BRIDGE B)

4

Do not tin the wires!

OUTPUT

70V

1

2

(BRIDGE)

1

1

2

Do not tin the wires!

1

2

OUTPUT