Amana BX521VE Owner's Manual

Download Owner's manual of Amana BX521VE Freezer for Free or View it Online on All-Guides.com.

Brand: Amana

Category: Freezer

Type: Owner's manual

Model: Amana BX521VE , Amana BX521VW

Pages: 21 (0.87 Mb)

Download Amana BX521VE Owner's manual

Amana BX521VE Owner's manual - Page 1
1
Amana BX521VE Owner's manual - Page 2
2
Amana BX521VE Owner's manual - Page 3
3
Amana BX521VE Owner's manual - Page 4
4
Amana BX521VE Owner's manual - Page 5
5
Amana BX521VE Owner's manual - Page 6
6
Amana BX521VE Owner's manual - Page 7
7
Amana BX521VE Owner's manual - Page 8
8
Amana BX521VE Owner's manual - Page 9
9
Amana BX521VE Owner's manual - Page 10
10
Amana BX521VE Owner's manual - Page 11
11
Amana BX521VE Owner's manual - Page 12
12
Amana BX521VE Owner's manual - Page 13
13
Amana BX521VE Owner's manual - Page 14
14
Amana BX521VE Owner's manual - Page 15
15
Amana BX521VE Owner's manual - Page 16
16
Amana BX521VE Owner's manual - Page 17
17
Amana BX521VE Owner's manual - Page 18
18
Amana BX521VE Owner's manual - Page 19
19
Amana BX521VE Owner's manual - Page 20
20
Amana BX521VE Owner's manual - Page 21
21
5
7. Place refrigerator door on center hinge. Tighten down
top hinge to securely hold door.
8. Use a dime at top to space door
11
/
16
"(18 mm)from
cabinet. Handle side of door should be approximately
1
/
8
" (3 mm) higher than hinge side. Door will become
level when it is loaded with food.
1/8"
(3 mm)
11/16"
(18 mm)
9. Replace hinge cover.
Note: If automatic ice maker water supply is
required, procede to
Connect Ice Maker Water
Supply Line
. If not, procede to section entitled
Leveling Refrigerator
.
Connect Ice Maker Water Supply Line
(some models)
DANGER
!
To avoid electrical shock which can cause severe
personal injury or death. Disconnect power to
refrigerator before connecting water supply.
CAUTION
!
Observe the following to avoid property damage:
Raise stabilizing leg before moving unit.
Make sure water pressure to water valve is
between 20 and 100 pounds per square inch.
Tighten adapter fitting and nuts with pliers and
wrenches. Do not overtighten.
Check for water leaks and correct if necessary
before returning refrigerator to normal location. After
24 hours check again for leaks.
Important
Before connecting water supply, contact a plumber to
connect coper tubing to household plumbing in
compliance with local codes and ordinances.
DO NOT use piercing type or
3
/
16
" saddle valves!
Both reduce water flow, become clogged with time and
in addition, may cause leaks if repair is attempted. The
correct type–a shut-off valve–requires a ¼" hole to be
drilled in the water supply pipe before valve attachment.
Do not install copper tubing in area where temperatures
drop below 32°F (0°C).
Materials Required
¼" O.D. (6 mm) flexible copper tubing
½" open end wrench
Length of copper tubing must reach from water supply
connection to water valve inlet port on back of
refrigerator, plus additional 8 ft. (2 m) of tubing for a
service loop. A service loop will allow refrigerator to be
pulled away from the wall without disconnecting tubing.
Procedure
1. Remove plastic cap
(A)
from water valve inlet port
(B)
.
A
B
2. Place brass nut
(A)
and brass sleeve
(B)
on copper
tubing
(C)
(Brass nut and sleeve are found in your
literature packet.). Insert copper tubing into water
valve inlet port
(D)
. Connect brass nut on copper
tubing to water valve inlet port. Make sure copper
tubing is secure by pulling on copper tubing.
3. Turn on water supply to refrigerator and check for
leaks. Correct any leaks at connection. Be careful not
to overtighten connection.
4. Create a service loop using extreme care to avoid
kinks. Secure copper tubing to refrigerator cabinet
with a "P" clamp
(E)
. It is important to secure copper
tubing to refrigerator to avoid leaks when pushing
refrigerator back into opening.
A
B
D
C
E
5. Proceed to
Leveling Refrigerator
for final refrigerator
placement.