First Alert CO5120BN User Manual

Download Operation & user’s manual of First Alert CO5120BN Carbon Monoxide Alarm for Free or View it Online on All-Guides.com.

Brand: First Alert

Category: Carbon Monoxide Alarm

Type: Operation & user’s manual for First Alert CO5120BN

Pages: 1 (1.01 Mb)

Download First Alert CO5120BN Operation & user’s manual

First Alert CO5120BN Operation & user’s manual - Page 1
1
INTRODUCTION
Thank you for choosing BRK Brands, Inc. for your Carbon Monoxide Alarm
needs. You have purchased a state-of-the-art Carbon Monoxide Alarm
designed to pr
ovide you with early warning of carbon monoxide.
Key featur
es include:
Most Accurate Carbon Monoxide Sensor*
Advanced electrochemical CO sensor technology.
Intelligent Sensing Technology is designed to help reduce unwanted or
nuisance alarms.
T
wo Silence Features.
T
emporarily silence low battery chirp for up to eight
hours befor
e replacing low battery or silence an unwanted alarm for several
minutes.
Two Latching Features. Alarm Latch: Easily identifies initiating alarm even
after alarm condition has subsided. Low Battery Latch: Identifies which unit
is in low battery condition.
Smart Interconnect interconnects with most First Alert
®
and BRK branded
smoke, CO and heat alarms. When inter
connected with alarming smoke
alarms, unit will sound smoke hor
n pattern.
Dust Cover is included to keep the alarm clean during construction.
Easy Installation/Maintenance featur
es include a large opening in the
mounting bracket for easy access to wiring. A battery pull tab keeps the
battery fr
esh until the home is occupied. A Side Load Battery Drawer allows for
easy battery r
eplacement without removing the alarm from the ceiling or wall.
© 2008 BRK Brands, Inc., a Jar
den Corporation company (NYSE: JAH)
3901 Liberty Str
eet Road, Aurora, IL 60504-8122
All rights reserved.
Consumer Af
fairs: (800) 323-9005 • www
.firstalert.com
BASIC SAFETY INFORMATION
Dangers, Warnings, and Cautions alert you to important
operating instr
uctions or to potentially hazar
dous situations.
Pay special attention to these items.
• THIS IS NOT A SMOKE ALARM! This CO Alarm is designed to
detect carbon monoxide fr
om ANY source of combustion. It is
NOT designed to detect smoke, fir
e, or any other gas.
• This CO Alarm is approved for use in single-family residences.
It is NOT designed for marine or R
V use.
This CO Alar
m will only indicate the pr
esence of carbon monoxide gas
at the sensor
. Carbon monoxide gas may be present in other areas.
This unit does not work without power
. If the AC power fails, the
battery back-up will power the alarm for at least 7 days provided
the 9V batter
y is fr
esh and cor
rectly installed.
The Silence Feature is for your convenience only and will not correct
a CO problem. Always check your home for a potential problem
after any alar
m. Failure to do so can result in injury or death.
This CO Alarm should receive continuous 120VAC, 60 Hz, pure sine
wave electrical power
. (The battery is meant for emergency back-
up only). Do not use in an extension cor
d or outlet contr
olled by a
dimmer or switch.
NEVER ignor
e any alarm. See “If Your CO Alarm Sounds” for more
information on how to respond to an alarm. Failure to respond can
r
esult in injur
y or death.
T
est this Carbon Monoxide Alar
m once a week. If it ever fails to
test correctly, have it replaced immediately! If the CO Alarm is not
working pr
operly, it cannot alert you to a problem.
This pr
oduct is intended for use in ordinary indoor locations of
family living units. It is not designed to measure CO levels in
compliance with Occupational Safety and Health Administration
(OSHA) commer
cial or industrial standards. Individuals with
medical conditions that may make them more sensitive to carbon
monoxide may consider using war
ning devices which pr
ovide
audible and visual signals for carbon monoxide concentrations
under 30 ppm. For additional information on carbon monoxide and
your medical condition contact your physician.
HOW YOUR CO ALARM WORKS
The Cover Of Your CO Alarm
UNDERSTANDING THE LIGHT AND HORN PATTERNS
M08-0002-003 Q 04/08 Printed in Mexico
IMPORTANT! PLEASE READ CAREFULLY AND SAVE.
This user’
s manual contains important information about your
CO Alarm’
s operation. If you are installing this CO Alarm for use by
others, you must leave this manual—or a copy of it—with the end user.
5 6 7 2 3
USER’S MANUAL
AC POWERED
CARBON MONOXIDE ALARM
120VAC ~, 60Hz, 0.09A
4
Printed in Mexico M08-0002-003 Q 04/08
First Alert
®
is a registered trademark of the First Alert Trust.
LIMITED WARRANTY
BRK Brands, Inc., ("BRK") the maker of First Alert
®
brand products warrants that for a period of five years from the date of purchase, this product will be free from
defects in material and workmanship. BRK, at its option, will repair or replace this product or any component of the product found to be defective during the warranty
period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar
product of equal or greater value. This is your exclusive warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is
not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. BRK dealers, service centers, or retail stores selling
BRK products do not have the right to alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or
current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorized service center. Further, the warranty
does not cover Acts of God, such as fire, flood, hurricanes and tornadoes or any batteries that are included with this unit.
BRK shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable
law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. Some states, provinces or
jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations
or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province.
How to Obtain W
ar
ranty Ser
vice
Ser
vice:
If service is r
equir
ed, do not return the product to your retailer. In order to obtain warranty service, contact the Consumer Affairs Division at 1-800-323-9005,
7:30 AM - 5:00 PM Central Standar
d Time, Monday thr
ough Friday
. T
o assist us in serving you, please have the model number and date of purchase available when
calling.
For Warranty Service return to: BRK Brands, Inc., 25 Spur Drive, El Paso, TX 79906
Battery: BRK Brands, Inc. make no warranty, express or implied, written or oral, including that of merchantability or fitness for any particular purpose
with respect to battery.
WEEKLY TESTING
Push and hold the T
est/Silence button until you hear an acknowledge chirp and
a loud alarm sounds — 4 beeps, pause, 4 beeps. This sequence should last for
10 seconds. If the Alarm ever fails to test pr
operly, replace it immediately. If the
Alarm is not working pr
operly
, r
efer to “Limited W
arranty”.
If the Alar
m ever fails to test pr
operly
, r
eplace it immediately
.
Pr
oducts under war
ranty may be returned to the manufacturer for
replacement. See “Limited Warranty” at the end of this manual.
DO NOT stand close to the Alarm when the horn is sounding.
Exposur
e at close range may be harmful to your hearing. When
testing, step away when hor
n starts sounding.
NEVER use vehicle exhaust! Exhaust may cause permanent damage
and voids your warranty.
REGULAR MAINTENANCE
To keep the CO Alarm working properly:
Test it every week as described in “Weekly Testing.”
V
acuum the CO Alarm cover at least once a month, using the soft brush
attachment. Never use water, cleaners, or solvents, since they may damage
the unit. T
est the Alarm again after vacuuming.
Replace the battery immediately when you see/hear the “Low Battery
W
arning”.
The Low (or Missing) Battery Warning (CO5120PDBN):
The horn will “chirp” once a minute and the word “bat” will flash on and off
on the display.
REPLACING THE BATTERY
Choosing a replacement battery: This unit requires one standard 9V alkaline
battery. The following alkaline batteries are acceptable as replacements:
Duracell #MN1604 or MX1604; Ever
eady “Ener
gizer” 522. These r
eplacement
batteries are commonly available at local retail stores.
Use only the alkaline or lithium replacement batteries listed. The unit may not
operate properly with other batteries. Never use rechargeable batteries since
they may not pr
ovide a constant charge.
DO NOT spray cleaning chemicals or insect sprays directly on or near
the CO Alarm. DO NOT paint over the CO Alarm. Doing so may cause
permanent damage.
Household cleaners, aer
osol chemicals and other contaminants can
affect the sensor. When using any of these materials near the CO Alarm,
make sur
e the room is well ventilated.
If your home is being fumigated, unplug the unit temporarily and put it
where it will not be exposed to chemicals or fumes. When fumigation is
complete and all traces of fumes clear
, plug the unit back in and r
etest it.
Standar
ds:
Underwriters Laboratories Inc. Single and Multiple Station carbon
monoxide alarms UL2034.
Accor
ding to Underwriters Laboratories Inc. UL2034, Section 1-1.2: “Carbon
monoxide alarms covered by these requirements are intended to respond to
the pr
esence of carbon monoxide from sources such as, but not limited to,
exhaust fr
om internal-combustion engines, abnormal operation of fuel-fired
appliances, and fir
eplaces. CO Alarms ar
e intended to alarm at carbon
monoxide levels below those that could cause a loss of ability to r
eact to the
dangers of Carbon Monoxide exposur
e.” This CO Alarm monitors the air at
the Alarm, and is designed to alarm before CO levels become life threatening.
This allows you pr
ecious time to leave the house and correct the problem.
This is only possible if Alarms ar
e located, installed, and maintained as
described in this manual.
Gas Detection at T
ypical Temperature and Humidity Ranges:
The CO Alarm
is not formulated to detect CO levels below 30 ppm typically
. UL tested for false
alarm resistance to Methane (500 ppm), Butane (300 ppm), Heptane (500 ppm),
Ethyl Acetate (200 ppm), Isopr
opyl Alcohol (200 ppm) and Carbon Dioxide (5000
ppm). V
alues measure gas and vapor concentrations in parts per million.
Audible Alar
m:
85 dB minimum at 10 feet (3 meters).
TROUBLESHOOTING GUIDE
Pr
oblem...
If the Alar
m..
Y
ou should...
Red light is OFF. Unit will not alarm when you press
the T
est/Silence button.
Unit may not be receiving any power. Check the AC power supply. Make sure the power
connector is secur
ely attached to the Alarm. Make
sure a fresh 9V battery is installed to power the
battery back-up.
Red light flashes once a minute (horn is silent).
(CO5120PDBN display r
eads “bat”).
Alarm is not receiving AC power. Unit is operating on DC battery back-up. Check the
AC power supply
.
The r
ed light flashes and the hor
n “chirps” once a
minute. (CO5120PDBN display flashes “bat”).
Low battery war
ning.
Replace the 9V battery in the battery back-up.
Disconnect AC power before changing the battery.
Once a minute, the alarm sounds 3 quick “chirps”,
and the red light flashes quickly three times.
(CO5120PDBN display r
eads “Err”).
MALFUNCTION SIGNAL. Based on its Self T
est
diagnostics, the unit has detected a malfunction.
The unit needs to be r
eplaced.
Make sur
e a fr
esh 9V battery is installed. If unit still
isn’t functioning– REPLACE IT. Units under warranty
should be r
etur
ned to manufacturer for replacement.
See “Limited Warranty” for details.
CO Alarm sounds fr
equently even though no high
levels of CO are revealed in an investigation.
The CO Alarm may be impr
operly located.
Refer to “Where to Install CO Alarms.”
Relocate your Alarm. If fr
equent alarms continue, have
home rechecked for potential CO problems. You may
be experiencing an intermittent CO problem.
IF YOUR CO ALARM SOUNDS
Actuation of your CO Alar
m indicates the presence of carbon monoxide (CO)
which can kill you. When your CO Alar
m sounds, you must not ignore it!
IF THE ALARM SOUNDS:
1.
Operate the Test/Silence button to silence the alarm.
2.
Call your emergency services, fire department or 911. Write down the
number of your local emer
gency service here:
________________________________________________________________
3. Immediately move to fresh air—outdoors or by an open door or window.
Do a head count to check that all persons ar
e accounted for. Do not re-
enter the pr
emises, or move away from the open door or window until the
emergency services responder has arrived, the premises have been aired
out, and your CO Alarm r
emains in its normal condition.
4.
After following steps 1-3, if your CO Alarm reactivates within a 24-hour period,
repeat steps 1-3 and call a qualified appliance technician to investigate for
sour
ces of CO from fuel-burning equipment and appliances, and inspect for
proper operation of this equipment. If problems are identified during this
inspection have the equipment serviced immediately. Note any combustion
equipment not inspected by the technician, and consult the manufactur
ers’
instructions, or contact the manufacturers directly, for more information about
CO safety and this equipment. Make sure that motor vehicles are not, and
have not, been operating in an attached garage or adjacent to the r
esidence.
Write down the number of a qualified appliance technician here:
__________________________
_______________________________________
Alar
ms have various limitations. See "General Limitations of CO Alarms"
for details.
USING THE SILENCE FEATURES
NEVER disconnect the power to your CO Alar
m to silence the horn—
use the silence feature. Disconnecting the CO Alarm removes your
pr
otection! See previous page for details on responding to an alarm.
The Silence Feature is intended to temporarily silence your CO Alarm’s alarm
horn while you correct the problem—it will not correct a CO problem. While the
Alarm is silenced, it will continue to monitor the air for CO.
When CO r
eaches
alarm level, the unit will sound— repeating horn pattern: 4 beeps, a pause, 4
beeps, etc. Press and hold the Test/Silence button until the horn is silent.
The Silence cycle will last approximately 4 minutes.
To silence an interconnected series of Alarms, you must press the Test/
Silence button on the initiating alarm (the unit with the flashing red light).
If you pr
ess the Test/Silence on any other Alarm, it will only silence that unit,
not the whole interconnected series.
NOTE: After the 4-minute silence cycle, the CO Alarm r
e-evaluates present CO
levels and responds accordingly. If CO levels remain potentially dangerous—or
start rising higher—the horn will start sounding again.
While the CO Alarm is silenced:
If the CO Alar
m...
is silent for only 4 minutes, then starts sounding loudly—4
beeps, then a pause, 4 beeps, then a pause. Red light (LED) continues flashing...
This means...CO levels are still potentially dangerous.
If the CO Alar
m...
r
emains silent....
This means...unit has r
eturned to normal operation.
SILENCING THE LOW BATTERY WARNING
This silence feature can temporarily quiet the low battery warning “chirp” for
up to 8 hours if AC
power is pr
esent. Press the Test/Silence button on the
alarm cover
. Once the low battery war
ning “chirp” silence featur
e is activated,
the unit continues to flash the red light once a minute for 8 hours. After 8
hours, the low battery “chirp” will r
esume.
Replace the batter
y as soon as
possible,
to maintain pr
otection in the event of a power outage.
LATCHING FEATURES
Alar
m Latch
is activated after an Alarm is exposed to alarm levels of carbon
monoxide. This featur
e will only work with AC power. After CO levels drop
below alarm levels, the Red LED will begin to flash On for 2 seconds and Of
f
for 2 seconds. It will continue to flash or “latch” until you clear it by testing
the Alarm.
This featur
e helps emergency responders, investigators, or service technicians
identify which unit(s) in your home wer
e exposed to alarm levels of carbon
monoxide. This can help investigators pinpoint the sour
ce of CO.
Inter
connected Alarms.
Latching Alarm Indicator shows which Alarm(s) in
the series wer
e exposed to alarm levels of carbon monoxide.
The Latching Alarm Indicator stays ON until you clear it, so it can alert you to
a CO Alarm that occurr
ed while you were away from home, even though CO
present in the air has dropped below alarm levels.
Low Batter
y Latch
is activated when the Alarm is in the "low battery
condition". When this occurs, the red LED flashes 4 seconds On/2 seconds
Off. This feature is designed to help you identify which Alarm needs to have
the battery r
eplaced. Although, the Alarm will sound the low battery chirp
approximately once every minute, sometimes during the initial stages of "low
battery", the Alarm will chirp in gr
eater intervals than one minute, sometimes
up to several hours, until the battery r
eaches a steady low battery level. This
innovative feature eliminates the frustration of waiting for and/or identifying
which unit is chirping.
The optional locking featur
es ar
e designed to pr
event unauthorized removal of
the battery or alarm. It is not necessary to activate the locks in single-family
households wher
e unauthorized battery or alarm removal is not a concern.
These CO Alarms have two separate locking features: one locks the battery
compartment, and the other locks the CO Alarm to the mounting bracket.
Y
ou can choose to use either feature independently, or use them both.
T
ools you will need:
• Needle-nose pliers • Standar
d Flathead scr
ewdriver
.
Both locking featur
es use locking pins, molded into the mounting bracket.
Using needle nose pliers remove one or both pins, depending on which locking
features you use.
USING THE LOCKING FEATURES
Locking Pin
THE BATTERY COMPARTMENT LOCK
TO LOCK THE BATTERY COMPARTMENT:
Do not lock the battery compartment until you have
activated the battery and tested the battery back-up.
1.
Activate the battery back-up by r
emoving the “Pull
to Activate Battery Back-Up” tab. Push and hold the
test button on the CO Alarm’s cover until you hear
an acknowledge chirp and the alarm sounds:
4 beeps, pause, 4 beeps, pause.
If the unit does not alarm during testing, DO
NOT lock the battery compartment! Install a new
batter
y and test again. If it still does not alar
m,
replace the CO Alarm immediately.
2. Using needle-nose pliers, detach
one locking pin from the mounting
bracket.
3.
Push the locking pin thr
ough the
black dot on the label on the back
of the CO Alarm.
TO UNLOCK THE
BATTERY COMPARTMENT:
Once the CO Alarm is installed, you must disconnect it from the AC power
before unlocking the battery compartment.
ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the
CO Alar
m is installed befor
e r
emoving it from the mounting bracket. Failure
to turn off the power first may result in serious electrical shock, injury or
death.
1. Remove the CO Alarm from the mounting bracket. If the unit is locked to
the bracket, see the section “To Deactivate the Locking Feature.”
2. Disconnect the power connector by gently prying it away from the back
of the CO Alarm.
3. Insert a flathead screwdriver under the head of
the locking pin, and gently pry it out of the
battery compartment lock. (If you plan to relock
the battery compartment, save the locking pin.)
4. To relock the battery compartment, close the
battery door and reinsert the locking pin in the
lock.
5.
Reconnect the power connector to the back of the CO Alarm, r
eattach
the CO Alarm to the mounting bracket, and restore the power.
When replacing the battery, always test the CO Alarm before relocking the
battery compartment.
THE MOUNTING BRACKET LOCK
T
ools you will need:
• Needle-nose pliers
• Standard Flathead screwdriver
TO ACTIVATE THE BRACKET LOCK:
1. Using needle-nose pliers, detach one locking
pin fr
om the mounting bracket.
2.
Insert the locking pin into the
lock located on the pivoting
hinge of the battery door.
3. When you attach the CO Alarm
to the mounting bracket, the
locking pin’
s head will fit into a
notch on the bracket.
TO DEACTIVATE THE BRACKET LOCK:
ELECTRICAL SHOCK HAZARD. T
ur
n of
f the power to the area where the
CO Alarm is installed before removing it from the mounting bracket.
Failure to turn off the power first may result in serious electrical shock,
injury or death.
Always discharge the branch circuit before servicing an AC or AC/DC
CO Alarm. First, turn off the AC power at the circuit breaker or fuse box.
Next, remove the battery from Alarms with battery back-up. Finally, press
and hold the test button.
1.
Insert a flathead screwdriver between the
mounting bracket pin and the mounting bracket.
2. Pry the CO Alarm away from the bracket by
tur
ning both the scr
ewdriver and the CO Alarm
counterclockwise (left) at the same time.
TO PERMANENTLY REMOVE
THE BRACKET LOCK:
Insert the flathead screwdriver
between the locking pin and the
lock, and pry the pin out of the lock.
INSTALLATION
WHERE TO INSTALL CO ALARMS
The National Fir
e Protection Association (NFPA) recommends that a CO Alarm
should be centrally located outside of each separate sleeping ar
ea in the
immediate vicinity of the bedr
ooms. For added protection, install additional
CO Alarms in each separate bedr
oom, and on every level of your home.
If your bedr
oom hallway is longer than 40 feet (12 meters), install a CO Alarm
at BOTH ends of the hallway
.
In a Single-level Home:
Install at least one CO Alarm near or within each separate sleeping ar
ea.
For added protection, install an additional CO Alarm at least 20 feet
(6 meters), away fr
om the fur
nace or fuel bur
ning heat sour
ce.
In a Multi-level Home
(same as above plus):
Install at least one CO Alarm near or within each separate sleeping ar
ea.
For added pr
otection, install at least one CO Alarm on each level of the
home. If you have a basement, install that CO Alarm at the top of the
basement stairs.
For added protection, install an additional CO Alarm at least 20 feet
(6 meters) away fr
om the fur
nace or fuel bur
ning heat sour
ce.
WHERE CO ALARMS SHOULD NOT BE INST
ALLED
DO NOT locate this CO Alarm:
In garages, kitchens, furnace rooms, or in any extremely dusty, dirty
or greasy areas.
Where combustion particles are produced. Combustion particles form
when something bur
ns. Ar
eas to avoid include poorly ventilated kitchens,
garages, and fur
nace r
ooms. Keep units at least 20 feet (6 meters) fr
om
the sources of combustion particles (stove, furnace, water heater, space
heater) if possible. In ar
eas wher
e a 20-foot (6 meter) distance is not
possible — in modular, mobile, or smaller homes, for example — it is
recommended the CO Alarm be placed as far from these fuel-burning
sour
ces as possible. The placement r
ecommendations ar
e intended to
keep these Alarms at a reasonable distance from a fuel-burning source,
and thus reduce “unwanted” alarms. Unwanted alarms can occur if a CO
Alarm is placed dir
ectly next to a fuel-bur
ning sour
ce. V
entilate these
ar
eas as much as possible.
Within 5 feet (1.5 meter) of any cooking appliance.
In extr
emely humid ar
eas. This Alarm should be at least 10 feet (3 meter)
from a bath or shower, sauna, humidifier, vaporizer, dishwasher, laundry
room, utility room or other source of high humidity.
In areas where temperature is colder than 40˚ F (4˚ C) or hotter than 100˚ F
(38˚ C). These areas include non-airconditioned crawl spaces, unfinished
attics, uninsulated or poorly insulated ceilings, por
ches, and garages.
In turbulent air
, like near ceiling fans, heat vents, air conditioners,
fresh air returns, or open windows. Blowing air may prevent CO from
reaching the sensors.
In direct sunlight.
This CO Alar
m is designed for use inside a single-family home or
apar
tment. It is not meant to be used in common lobbies, hallways,
or basements of multi-family buildings unless working CO Alarms
ar
e also installed in each family living unit. CO Alar
ms in common
areas may not be heard from inside individual family living units.
This CO Alar
m alone is not a suitable substitute for complete
detection systems in places which house many people, like hotels
or dormitories, unless a CO Alarm is also placed in each unit.
DO NOT use this CO Alar
m in war
ehouses, industrial or commer
cial
buildings, special-purpose non-residential buildings, RVs, boats,
or airplanes. This CO Alar
m is specifically designed for residential
use, and may not pr
ovide adequate pr
otection in non-r
esidential
applications.
G
ARAGE
SUGGESTED AREAS FOR INSTALLING ADDITIONAL CO ALARMS
BEDROOM
BEDROOM
HALL
LIVING ROOM
KITCHEN
B
ASEMENT
BEDROOM
R
EQUIRED TO MEET NFPA RECOMMENDATIONS
BEFORE YOU BEGIN INSTALLATION
This unit is designed to be mounted on any standar
d wiring junction box up
to a 4-inch (10 cm) size, on either the ceiling or wall. Read “Where to Install CO
Alarms” and “Wher
e Not To Install CO Alarms” before you begin installation.
• This Alarm must have AC or battery power to operate. If the AC
power fails, the battery back-up will power the Alarm for a short
time if the 9V batter
y is fresh and correctly installed. If AC power
fails, and the battery is dead or missing, the Alarm cannot operate.
• Make sure the alarm is not receiving excessive noisy power.
Examples of noisy power could be major appliances on the same
circuit, power from a generator or solar power, light dimmer on the
same circuit or mounted near fluorescent lighting. Excessive noisy
power may cause damage to your Alar
m.
Find the pair of self-adhesive labels included with this CO Alarm.
On each label write in the phone number of your emergency responder
(like 911) and a qualified appliance technician.
• Place one label near the CO Alarm, and the other label in the “fresh air”
location you plan to go if the alarm sounds.
NOTE: A qualified appliance technician is defined as “a person, firm, corporation,
or company that either in person or thr
ough a representative, is engaged in and
r
esponsible for the installation, testing, servicing, or replacement of heating,
ventilation, air conditioning (HVAC) equipment, combustion appliances and
equipment, and/or gas fir
eplaces or other decorative combustion equipment.”
P
ARTS OF THIS CO ALARM
1 Mounting Bracket
2
Mounting Slot and Screw
*
3 Locking Pins (break out of
bracket)
4 Hot (Black) AC Wire
5
Neutral (White) AC Wire
6 Interconnect Wire (Orange)
7
Lever to Open Battery
Compartment
8 Swing-Out Battery
Compartment
9
Quick-Connect Power
*Not Included
1
2
3
2
9
8
7
3
5
6
4
Tools you will need: Standard Flathead screwdriver.
ELECTRICAL SHOCK HAZARD. T
urn off power to the area where you
will install this unit at the circuit breaker or fuse box before beginning
installation. Failur
e to turn off the power before installation may result
in serious electrical shock, injur
y or death.
T
o install this unit:
1.
Remove the mounting bracket from the base. Position the screw
slots on the mounting bracket over the scr
ews in the junction box.
Tighten the scr
ews.
2.
Using wire nuts, connect the power connector to the AC power.
Impr
oper wiring of the power connector or the wiring leading to the
power connector will cause damage to the Alar
m and may lead to a
non-functioning Alar
m.
3. Plug the power connector into the back of the CO Alarm.
4. Position the base of the Alarm over the mounting bracket and turn.
The Alarm can be positioned over the bracket every 60
°. Turn the unit
clockwise (right) until the unit is in place.
5.
Check all connections.
ST
AND ALONE ALARM ONL
Y
:
Connect the white wire on the power connector to the neutral wire
in the junction box.
Connect the black wire on the power connector to the hot wire in
the junction box.
Tuck the orange wire inside the junction box.
It is used for
inter
connect only.
INTERCONNECTED ALARMS ONL
Y
:
Strip of
f about 1/2” of the plastic coating on the orange interconnect
wir
e on the power connector.
Connect the white wire on the power connector to the neutral wire
(usually white) in the junction box.
Connect the black wir
e on the power connector to the hot wir
e (usual
-
ly black) in the junction box.
Connect the orange wire on the power connector to the interconnect
wir
e in the junction box. Repeat for each unit you ar
e inter
connecting.
Never connect the hot or neutral wir
es in the junction box to the
orange inter
connect wire.
SPECIAL REQUIREMENTS FOR INTERCONNECTED CO ALARMS
Failure to meet any of the above requirements could damage the
units and cause them to malfunction, r
emoving your protection.
• AC and AC/DC CO Alarms can be interconnected. Under AC power,
all units will alarm when one senses CO. When power is interrupted,
only the AC/DC units in the series will continue to send and r
eceive
signals. AC power
ed CO Alarms will not operate.
Inter
connected units can provide earlier warning of a CO problem than stand-
alone units, especially if the problem starts in a remote area of the dwelling.
If any unit in the series senses CO, all CO and Smart Interconnect units will
alarm. T
o determine which CO Alarm initiated an alarm, refer to the table.
On Initiating CO Alarm Red LED Flashes the alarm pattern
On All Other CO Alarms Red LED Does Not Flash the alarm pattern
Inter
connect units within a single family residence only. Otherwise all house-
holds will experience unwanted alarms when you test any unit in the series.
Inter
connected units will only work if they ar
e wired to compatible units and
all r
equirements are met.
This unit is designed to be compatible with:
BRK Electr
onics
®
and First Aler
t
®
Models 7010, 7010B, 7020B, SC7010B,
SA520B, 9120, 9120B, SC9120B, 100S, SL177,
SC7010BV
,
CO5120BN,
CO5120PDBN, HD6135F
, HD6135FB.
Inter
connected units must meet ALL of the following requirements:
A maximum of 18 compatible Smoke, Heat or CO Alarms may be
inter
connected. No more than 12 of the 18 can be Smoke Alarms per
NFP
A 72.
The same fuse or cir
cuit br
eaker must power all inter
connected units.
The total length of wire interconnecting the units should be less than
1000 feet. This type of wire is commonly available at Hardware and
Electrical Supply stor
es.
All wiring must conform to all local electrical codes and Articles 210 and
300.3 (B) of the National Electrical Code. Refer to your local building
code for further connection r
equirements.
6.
Make sur
e the CO Alarm is receiving AC power. Under normal operation,
the r
ed indicator light will shine continuously.
If the r
ed power indicator light
does not light, TURN OFF POWER TO THE JUNCTION BOX and recheck
all connections. If all connections ar
e correct and the red power indicator
still does not light when you r
estore the power, the unit should be
replaced immediately.
7. ACTIV
ATING THE BATTERY BACK-UP
Activate the battery back-up by r
emoving the “Pull to Activate Battery
Back-Up” tab. You do not need to open the battery compartment and
reposition the battery during installation.
DO NOT remove the battery
activation tab until AC power is tur
ned on to conserve battery power.
8. Test the CO Alarm. Press and hold the test button on the cover until the
alarm sounds: 4 beeps, pause, 4 beeps, pause. In a series of inter
connected
Alarms, you must test each Alarm separately by pr
essing and holding the
test button. Make sure all units alarm when each one is tested.
If any unit in the series does not alarm during testing, TURN OFF POWER
and recheck connections. If it does not alarm when you restore power,
replace it immediately.
6
7
8
4
3
1
5
4
3
1
5
2
A
B
}
}
A. Unswitched 120VAC B. To Additional Alarms,
60 Hz sour
ce
Maximum = 18 Alarms
1. CO Alarm
2. Ceiling or Wall
3. Power Connector
4. Wir
e Nut
5. Junction Box
6. Neutral Wir
e (White)
7.
Interconnect Wire
(Orange)
8. Hot Wir
e (Black)
STAND ALONE ALARM ONLY:
If you are only installing one unit, restore power to the junction box.
INTERCONNECTED ALARMS ONLY:
If you are interconnecting multiple Alarms, repeat Step 1-5 for
each Alarm in the series. When you are finished, restore power
to the junction box.
ELECTRICAL SHOCK HAZARD. Do not r
estore power until all Alarms are
completely installed. Restoring power before installation is complete may
r
esult in serious electrical shock, injury or death.
HOW TO INSTALL YOUR CO ALARM
FINDING THE SOURCE OF CO AFTER AN ALARM
Carbon monoxide is an odorless, invisible gas, which often makes it difficult
to locate the sour
ce of CO after an alarm. These are a few of the factors that
can make it difficult to locate sources of CO:
House well ventilated before the investigator arrives.
• Problem caused by “backdrafting.”
• Transient CO problem caused by special circumstances.
Because CO may dissipate by the time an investigator arrives, it may be
difficult to locate the source of CO.
BRK Brands, Inc. shall not be obligated
to pay for any carbon monoxide investigation or ser
vice call.
POTENTIAL SOURCES OF CO IN THE HOME
Fuel-bur
ning appliances like:
portable heater, gas or wood
bur
ning fireplace, gas kitchen range
or cooktop, gas clothes dryer
.
Damaged or insuf
ficient
venting:
corroded or disconnected
water heater vent pipe, leaking
chimney pipe or flue, or cracked
heat exchanger, blocked or
clogged chimney opening.
Improper use of appliance/
device:
operating a barbecue grill
or vehicle in an enclosed area (like
a garage or screened porch).
Transient CO Problems: “transient” or on-again-off-again CO problems can
be caused by outdoor conditions and other special cir
cumstances.
The following conditions can result in transient CO situations:
1.
Excessive spillage or r
everse venting of fuel appliances caused by outdoor
conditions such as:
• Wind direction and/or velocity, including high, gusty winds. Heavy air in
the vent pipes (cold/humid air with extended periods between cycles).
Negative pressure differential resulting from the use of exhaust fans.
• Several appliances running at the same time competing for limited fresh air.
• Vent pipe connections vibrating loose from clothes dryers, furnaces, or
water heaters.
• Obstructions in or unconventional vent pipe designs which can amplify
the above situations.
2.
Extended operation of unvented fuel bur
ning devices (range, oven, fireplace).
3.
Temperature inversions, which can trap exhaust close to the ground.
4. Car idling in an open or closed attached garage, or near a home.
These conditions are dangerous because they can trap exhaust in your home.
Since these conditions can come and go, they ar
e also har
d to r
ecr
eate during
a CO investigation.
CO Alarm goes back into alarm 4 minutes after
you pr
ess the Test/Silence button.
CO levels are still potentially dangerous. Refer to “If Your CO Alarm Sounds” for details on
how to r
espond to an alarm. If anyone is feeling ill,
EVACUATE your home immediately and call 911.
This CO Alarm is intended for residential use. It is not intended for use in
industrial applications wher
e Occupational Safety and Health Administration
(OSHA) r
equirements for carbon monoxide detectors must be met.
CO alar
ms may not waken all individuals.
If childr
en or others do not readily
waken to the sound of the CO alarm, or if ther
e ar
e infants or family members
with mobility limitations, make sur
e that someone is assigned to assist them
in the event of an emer
gency
.
CO Alar
ms will not work without power
.
This CO Alarm r
equir
es a continuous
supply of AC power, and a fresh, correctly installed 9V battery to power the
battery back-up. The battery back-up is for emer
gency use only!
CO Alar
ms for Solar or Wind Energy users and battery backup power
systems:
AC power
ed CO Alarms should only be operated with true or pur
e
sine wave inverters. Operating this CO Alarm with most battery-power
ed UPS
(uninterruptible power supply) pr
oducts or square wave or “quasi sine wave”
inverters
will damage the Alarm. If you are not sure about your inverter or
UPS type, please consult with the manufactur
er to verify
.
This CO Alar
m will not sense carbon monoxide that does not r
each the
sensor.
This CO Alarm will only sense CO at the sensor. CO may be present
in other areas. Doors or other obstructions may affect the rate at which CO
r
eaches the CO Alarm. For this reason, if bedroom doors are usually closed
at night, we recommend you install a CO Alarm in each bedroom and in the
hallway between them.
CO Alar
ms may not sense CO on another level of the home.
For example,
a CO Alarm on the second level, near the bedr
ooms, may not sense CO in
the basement. For this reason, one CO Alarm may not give adequate warning.
Complete coverage is r
ecommended. Place CO Alarms on each level of the
home.
CO Alarms may not be heard. The Alarm horn loudness meets or exceeds
curr
ent UL standards of 85 dB at 10 feet (3 meters). However, if the CO Alarm
is installed outside the bedr
oom, it may not wake up a sound sleeper or one
who has r
ecently used drugs or has been drinking alcoholic beverages. This
is especially true if the door is closed or only partly open. Even persons who
ar
e awake may not hear the alarm hor
n if the sound is blocked by distance or
closed doors. Noise from traffic, stereo, radio, television, air conditioner, or
other appliances may also pr
event alert persons from hearing the alarm horn.
This CO Alarm is not intended for people who ar
e hearing impair
ed.
CO Alar
ms ar
e not a substitute for a smoke alar
m.
Although fir
e is a sour
ce
of carbon monoxide, this CO Alarm does not sense smoke or fire. This CO
Alarm senses CO that may be escaping unnoticed fr
om malfunctioning
fur
naces, appliances, or other sources. Early warning of fire requires the
installation of smoke alarms.
CO Alar
ms ar
e not a substitute for life insurance.
Though these CO Alarms
war
n against increasing CO levels, BRK Brands, Inc. does not warrant or imply
in any way that they will protect lives from CO poisoning. Homeowners and
renters must still insure their lives.
CO Alar
ms have a limited life.
Although the CO Alarm and all of its parts have
passed many stringent tests and ar
e designed to be as reliable as possible,
any of these parts could fail at any time. Ther
efor
e, you must test your CO
Alarm weekly
.
CO Alar
ms are not foolproof.
Like all other electr
onic devices, CO Alarms
have limitations. They can only detect CO that reaches their sensors. They
may not give early warning to rising CO levels if the CO is coming from a
r
emote part of the home, away fr
om the CO Alarm.
UNDERWRITERS LABORATORIES INC. UL2034
WHA
T LEVELS OF CO CAUSE AN ALARM?
Underwriters Laboratories Inc. Standar
d UL2034 requires residential CO
Alarms to sound when exposed to levels of CO and exposure times as
described below
. They are measured in parts per million (ppm) of CO over
time (in minutes).
UL2034 Requir
ed Alarm Points*:
If the Alarm is exposed to 400 ppm of CO, IT MUST ALARM BETWEEN
4 and 15 MINUTES
If the Alarm is exposed to 150 ppm of CO, IT MUST ALARM BETWEEN
10 and 50 MINUTES.
• If the Alarm is exposed to 70 ppm of CO, IT MUST ALARM BETWEEN
60 and 240 MINUTES.
* Approximately 10% COHb exposure at levels of 10% to 95% Relative
Humidity (RH).
The unit is designed not to alarm when exposed to a constant level
of 30 ppm for 30 days.
CO Alarms are designed to alarm before there is an immediate life threat.
Since you cannot see or smell CO, never assume it’
s not present.
An exposure to 100 ppm of CO for 20 minutes may not affect average,
healthy adults, but after 4 hours the same level may cause headaches.
An exposure to 400 ppm of CO may cause headaches in average,
healthy adults after 35 minutes, but can cause death after 2 hours.
GENERAL LIMIT
A
TIONS OF CO ALARMS
ELECTRICAL SHOCK HAZARD. T
urn off the power to the area where
the CO Alar
m is installed BEFORE r
emoving it fr
om the mounting
bracket or checking any electrical connections! Failure to turn off the
power first may r
esult in serious electrical shock, injur
y or death.
The following guide can help you identify a potential pr
oblem with the
installation or operation of your CO Alarm. NOTE: It is not meant to be
an all-inclusive list of all CO Alar
m conditions.
If you ar
e experiencing a
condition not covered in the next several pages, please contact Consumer
Af
fairs.
Condition
LED (Red Light) Horn
POWER UP
On continuously with AC
Silent
Flash a minute with battery
DURING TESTING LED flashes approximating Horn pattern:
the hor
n pattern. 4 beeps, pause,
4 beeps, pause
LOW OR MISSING
Low battery Latch Patter
n
Horn “chirps”
BA
TTER
Y
once a minute
W
ARNING: When the AC power is Off, if the battery is dead or missing,
the CO Alar
m cannot work.
ALARM CONDITION LED flashes approximating Horn pattern:
Single CO Alarm the horn pattern. 4 beeps, pause,
(Stand alone Alarm) 4 beeps, pause,
repeating
ALARM CONDITION LED flashes rapidly on the unit(s) Horn pattern:
(Interconnected that triggered the alarm. LEDs 4 beeps, pause,
Series of CO Alarms) on the other Alarms in the series repeating on all
will not flash
CO Alarms
ALARM SILENCE LED flashes approximating Horn stays quiet
the horn pattern. for 4 minutes
LOW BATTERY LED flashing approximately Horn is Silent for
SILENCE every minute. up to 8 hours.
ALARM LATCH Audio Off and LED flashing Horn is Silent
2 seconds On, 2 seconds Off
after local alarm unless reset
by Test/Silence button.
LOW BATTERY LED flashing 4 seconds On, Horn is Silent
LATCH 2 seconds Off.
NOTE: Latching features are not active during battery backup mode
operation.
MALFUNCTION LED flashes 3 times Horn sounds
synchronized with 3 rapid chirps 3 rapid chirps
(chirp-chirp-chirp)
every minute
1
HOW YOUR
CO ALARM WORKS, Continued
ADDITIONAL FEA
TURES FOR MODEL CO5120PDBN
WITH DIGITAL DISPLAY
Alarm operating
on AC power
Alarm operating
on emer
gency
battery back-up
Low / missing
battery war
ning
“Err” Alarm is
not operating
properly
USING THE PEAK CO MEMOR
Y
The CO Memory Feature lets you check the highest level of CO recorded
during an alarm.
To check CO Memory:
1. Press and release the Test/Silence/Scroll button until the dash scrolls
to “MEMOR
Y”.
2.
Press and hold Test/Silence/Scroll button to display Memory CO level.
To clear CO Memory:
1. Press and release the Test/Silence/Scroll button until the dash scrolls to
“CLEAR MEMOR
Y. ”
2. Press and hold the Test/Silence/Scroll button until the display shows “CLr.”
NOTE: The highest CO level will be saved, even after a power interruption,
until you clear it. DO NOT clear the CO Memory reading if you plan to call
someone to investigate a CO pr
oblem! Clear the CO Memory reading only
after the investigator has checked your home.
SMART INTERCONNECT FEATURE
This CO Alarm includes “Smart Inter
connect” which enables the Alarm to be
inter
connected with other BRK Smoke and CO Alarms. When interconnected
to Smoke Alarms that go into alarm, this CO Alarm will sound the smoke
hor
n pattern.
INST
ALLATION, continued
SYMPTOMS OF CO POISONING
These symptoms ar
e related to CO POISONING and should be discussed
with ALL household members.
Mild Exposure: Slight headache, nausea, vomiting, fatigue (“flu-like” symptoms).
Medium Exposur
e:
Thr
obbing headache, drowsiness, confusion, fast heart rate.
Extr
eme Exposure:
Convulsions, unconsciousness, heart and lung failur
e.
Exposure to Carbon Monoxide can cause brain damage, death.
This CO Alarm measur
es exposure to CO over time. It alarms if CO levels
are extremely high in a short period of time, or if CO levels reach a certain
minimum over a long period of time. The CO Alarm generally sounds an alarm
befor
e the onset of symptoms in average, healthy adults.
Why is this important? Because you need to be war
ned of a potential CO
pr
oblem while you can still react in time. In many reported cases of CO
exposure, victims may be aware that they are not feeling well, but become
disoriented and can no longer r
eact well enough to exit the building or get
help. Also, young childr
en and pets may be the first affected. The average
healthy adult might not feel any symptoms when the CO Alarm sounds.
However, people with cardiac or respiratory problems, infants, unborn babies,
pr
egnant mothers, or elderly people can be more quickly and severely affected
by CO. If you experience even mild symptoms of CO poisoning, consult your
doctor immediately!
WHA
T YOU NEED TO KNOW ABOUT CO
WHAT IS CO?
CO is an invisible, odorless, tasteless gas produced when fossil fuels do not
burn completely, or are exposed to heat (usually fire). Electrical appliances
typically do not produce CO.
These fuels include: Wood, coal, charcoal, oil, natural gas, gasoline, kerosene,
and propane.
Common appliances are often sources of CO. If they are not properly main-
tained, are improperly ventilated, or malfunction, CO levels can rise quickly.
CO is a r
eal danger now that homes ar
e mor
e ener
gy ef
ficient. “Air-tight”
homes with added insulation, sealed windows, and other weatherpr
oofing
can “trap” CO inside.
HOW CAN I PROTECT MY FAMILY?
A CO Alarm is an excellent means of pr
otection. It monitors the air and sounds
a loud alarm before carbon monoxide levels become threatening for average,
healthy adults.
A CO Alar
m is not a substitute for proper maintenance of home appliances.
To help prevent CO problems and reduce the risk of CO poisoning:
Clean chimneys and flues yearly. Keep them free of debris, leaves, and
nests for proper air flow. Also, have a professional check for rust and
corrosion, cracks, or separations. These conditions can prevent proper
air movement and cause backdrafting. Never “cap” or cover a chimney
in any way that would block air flow.
Test and maintain all fuel-burning equipment annually. Many local gas
or oil companies and HV
AC companies offer appliance inspections for
a nominal fee.
Make regular visual inspections of all fuel-burning appliances. Check
appliances for excessive rust and scaling. Also check the flame on the
burner and pilot lights. The flame should be blue. A yellow flame means
fuel is not being bur
ned completely and CO may be present. Keep the
blower door on the fur
nace closed. Use vents or fans when they are
available on all fuel-burning appliances. Make sure appliances are vented
to the outside. Do not use grills or barbecue indoors, or in garages or
on scr
een porches.
• Check for exhaust backflow from CO sources. Check the draft hood on
an operating fur
nace for a backdraft. Look for cracks on furnace heat
exchangers.
• Check the house or garage on the other side of shared wall.
Keep windows and doors open slightly. If you suspect that CO is escaping
into your home, open a window or a door. Opening windows and doors
can significantly decrease CO levels.
WITH BA
TTERY BACK-UP
Model CO5120BN
WITH BA
TTERY BACK-UP
AND DIGITAL DISPLAY
Model CO5120PDBN
For your records, please record:
Date Purchased: ______________Where Purchased: _____________________
Date Installed: ____________/____________Month/Y
ear
Replacement date is five years after installation:
_____________/____________Month/Year
NOTE: End of Life Signal — Once the unit r
eaches the end of its lifecycle,
the MALFUNCTION SIGNAL will sound once a minute to indicate the need
to immediately replace the Alarm.
LISTED TO
UL 2034
STANDARD
2
1
5
3
4
1.
T
est/Silence Button or
Test/Silence/Scroll Button
(CO5120PDBN only)
2. POWER/ALARM Light (RED)
3. Air V
ents
4.
(Behind the Cover) Alarm Hor
n:
85 dB audible alarm for test, alarm,
and unit malfunction war
ning.
5. Digital Display (CO5120PDBN only)
Levels of CO shown
in ppm if pr
esent.
During T
esting, the display flashes "30, 70, 150, 400" briefly.
During initial power up display flashes "888" briefly.