American Audio ELX Series User Instructions

Download User instructions of American Audio ELX Series Amplifier for Free or View it Online on All-Guides.com.

Brand: American Audio

Category: Amplifier

Type: User instructions for American Audio ELX Series

Pages: 18 (1.64 Mb)

Download American Audio ELX Series User instructions

American Audio ELX Series User instructions - Page 1
1
American Audio ELX Series User instructions - Page 2
2
American Audio ELX Series User instructions - Page 3
3
American Audio ELX Series User instructions - Page 4
4
American Audio ELX Series User instructions - Page 5
5
American Audio ELX Series User instructions - Page 6
6
American Audio ELX Series User instructions - Page 7
7
American Audio ELX Series User instructions - Page 8
8
American Audio ELX Series User instructions - Page 9
9
American Audio ELX Series User instructions - Page 10
10
American Audio ELX Series User instructions - Page 11
11
American Audio ELX Series User instructions - Page 12
12
American Audio ELX Series User instructions - Page 13
13
American Audio ELX Series User instructions - Page 14
14
American Audio ELX Series User instructions - Page 15
15
American Audio ELX Series User instructions - Page 16
16
American Audio ELX Series User instructions - Page 17
17
American Audio ELX Series User instructions - Page 18
18
©American Audio® - www.americanaudio.us - ELX Series Power Amplifier User Manual Page 9
SPEAKON ASSEMBLY: You will need a pair of Neutrik Speakon® NL4FC
connectors. You will also need high-quality two or four conductor speaker
cable, a pair of needle-nosed pliers and a 1.5-mm Allen key to assemble the
Speakon connectors to your speaker wire. To assemble the Neutrik Speakon
NL4FC connector, complete the following steps:
1. Strip back 3/4-inch of the cable casing. Strip off 1/4-inch from the end of
each of the conductors down to bare wire, and insert the brass ttings. See
Figure 5.
2. Slide the cable tension clip (D) and the speakon coupler (E) through the
cable end. See Figure 6.
3. Insert each wire with the brass ttings into the top of appropriate slot of the
connector insert (B) as shown in Figures 9 and 10. Use a 1.5-mm Allen key to
tighten the connection. See Figure 7.
4. Be sure to properly match the positive (+) and negative (–) leads of each
wire. See Figure 8.
5. Slide the connector insert (B) into the connector housing (A), making sure
that the large notch on the outer edge of the insert lines up with the large
groove on the inside of the connector housing. The insert should slide easily
through the housing and out the other side until it extends approximately 3
/4-inch from the end of the housing.
6. Slide the cable tension clip (D) along the cable and insert into the housing
(A), making sure that the large notch lines up with the large groove on the
inside of the connector housing (A). The cable tension clip (D) should slide
easily into the housing until only 3 /8-inch of the cable tension clip (D) extends
from the back end of the connector.
7. Slide the coupler (E) along the cable and screw it onto the end of the housing
(A). Before tightening, you may want to test the connector to make sure it has
been assembled properly.
Figure 5
C 1C 2
UTPUTS
CAUTION
MINIMUM LOAD IMPEDANCE 2 OHM PERCHANNEL 4 OHM BRIDGE
INPUT T UINPUT BA ANCE
120 60
4800 ATTS
SPEAKON 1+ HOT
1 COLD
C 1C 2
-+
-+
N
- BIDE +
+
+1
-1
+2
+2
+
+1
-1
+2
+2
Figure 8
Figure 7
4-Conductor Speaker CableBrass Inserts
Figure 6
D EBA C