Frigidaire FAH10ES2TA12 Installation Instructions Manual

Download Installation instructions manual of Frigidaire FAH Air Conditioner for Free or View it Online on All-Guides.com. This version of Frigidaire FAH Manual compatible with such list of devices, as: FAH, FAH086S1TA13, FAH08ES1TA11, FAH10ES2TA11, FAH126S2TA12

Frigidaire FAH Installation instructions manual - Page 1
1
Frigidaire FAH Installation instructions manual - Page 2
2
Frigidaire FAH Installation instructions manual - Page 3
3
Frigidaire FAH Installation instructions manual - Page 4
4
Frigidaire FAH Installation instructions manual - Page 5
5
Frigidaire FAH Installation instructions manual - Page 6
6
Frigidaire FAH Installation instructions manual - Page 7
7
Frigidaire FAH Installation instructions manual - Page 8
8
Frigidaire FAH Installation instructions manual - Page 9
9
Frigidaire FAH Installation instructions manual - Page 10
10
Frigidaire FAH Installation instructions manual - Page 11
11
Frigidaire FAH Installation instructions manual - Page 12
12
Installation instructions
Do This First
(for existing sleeve)
Note that the air conditioner dimensions are: 24.wide,
14½.high, and 18½. deep (without front). Install Air
Conditioner according to these installation instructions
to achieve the best performance. Save these installation
instructions for future reference.
Items in Kit
You may not need all parts in the kit. Discard unused
pans. Qty.
Tapered Spacer Blocks 17,,Long 2
Centering/Support Blocks 4½.x 3½.x 1½. 4
Plastic Divider 1/8" x 4½.x 14½,, 2
Stuffer Seal 1. x 1½"x 84,, 1
Seal 1½.x 1½.x 25,, 3
Seal 1½,,x 1½.x 14,, 2
Seal 1½.x 3/8.x 25. 3
Seal 1½.x 3/8.x 14,, 2
Seal 1" x 3/4.x 14,, 2
Trim Frame (side legs) 2
Trim Frame (top & bottom legs) 2
Ground Wire (green) 1
Nut for grounding screw 1
Grounding Screw 1
Grille (plastic) 1
Grille Aluminum 1
Nuts (plastic) 4
Screw w/washer 4
How to Install
1. identifythe wall-sleeve brandfor your installation,
from the chart below.
Brand
White-Westinghouee
Frigidaire
Carrier (52F Series)
General Electric/
Hotpoint
Whirlpool
Wall Sleeve Dimensions
(inches)
Width Height Depth
}25½ 15¼ 17½
16,
or 22
26 15%
25¼ 16½
Fedders/Emerson 27 16¾
16'/,
17½
or 23
16¾
or 19¾
18%
15
18%
16¾
Sears/Kenmore 25¾ 16½
Emerson/Fedders 26¾ 15¾
Carrier (51S Series) 25¾ 167/,
Friedrich 27 16¾
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition and
have a rear grille that securely attaches to sleeve, or
rear flange that serves as a stop for the Air Conditioner.
CAUTION: When installation is complete, replacement
unit MUST have a rearward
slope as shown.
1/4" 1o 5/16"
81eeve
REAR
L
2. Remove old Air Conditioner from wall sleeve and
prepare wall sleeve as follows:
-- Clean interior (do not disturb seals).
-- Wall sleeve must be securely fastened in wall before
installing Air Conditioner. Drive more nails or screws
through sleeve, into wall, if needed.
-- Repair paint if needed.
3. If not existing, drill a 3/16.clearance hole for ground-
ing screw through left side of wall sleeve, in a clear area
about 3 inches maximum (to suit) back from front edge
of sleeve as shown below. Next attach ground wire inside
sleeve, using grounding screw, nut washer pull loose
end of ground wire out front of sleeve, and temporarily
bend it down and around lower edge of sleeve.
Wall sleeve to unit
sleeve grounding
J
3/16"
F Hole
4. Prepare the wall sleeve for installation of the new unit
per the following Brand instructions.
#1 Emerson
#2 Fedders
#3 Fedders or Friedrich
#4 General Electric/Hotpoint
#5 Sears or Carrier (51S Series)
#6 Whirlpool
#7 Whirlpool
#8 White-Westinghouse/Frigidaire/
Carrier (52F Series)
#9 White-Westinghouse/Frigidaire
15"Deep
l_A,,Deep
16¾,,Deep
16¼,,Deep
18%,,Deep
17'_,,Deep
23.Deep
16,,+ 17½.Deep
22"Deep
5. Install new unit into wall sleeve.
6. To attach ground wire to the new unit, remove the
screw from the left side front.
7. Assemble and installthe
Trim Frame (see instruction).
P/N 66129901165