• Home
• Brands
• AMX Manuals
• AMX AF-10
• Amx AF-10 Install Manual

Amx AF-10 Install Manual

Download Quick start manual of AMX AF-10 Amplifier, Media Converter for Free or View it Online on All-Guides.com. This version of AMX AF-10 Manual compatible with such list of devices, as: AF-10, FG1010-70, FG1040-452, FG1040-455

1

2

Quick Start Guide

AutoPatch S-Video DA Modules & AF-10 Boards

Overview

S-Video Distribution Amplifier (DA) boards are available as either standalone

distribution amplifier modules (left in FIG. 1) or as distribution amplifier accessory

boards for an AF-10 (right in FIG. 1). The S-Video DA Module has one input and four

outputs for a 1:4 distribution. S-Video DA boards have five S-Video connectors; either

one input and four outputs or five outputs that are paired with the 1:4 board to create a

1:9 distribution amplifier.

Product Specifications

Product specifications below are specifically for AMX AutoPatch S-Video cables.

Installation

S-Video 1:4 Distribution Amplifier Module

Module Mounting Options

Desktop – Attach the rubber feet (included) on the bottom of the module.

Rack Trays & Mounting Brackets – contact your AMX representative for details.

Module System Setup

The S-Video DA Module has five S-Video connectors, one input and four outputs.

AF-10 with 1:4 & 5-out S-Video Distribution Amplifier Boards

Board System Set-up

S-Video DA 1:4 and 5-out boards are available for the AMX AutoPatch AF-10

Accessory Card Frame. The 1:4 board is built to use alone or in conjunction with the

5-out board. When using both, these boards must be installed in adjoining slot pairs,

with the 5-out board to the left of the 1:4 board for a 1:9 distribution.

Attaching Cables

Note: AMX AutoPatch S-Video cables lock onto S-Video connectors. Standard

S-Video cables may be used, but will not lock.

To attach a locking S-Video connector:

1. Hold the connector at a slight angle to the right while pushing in or pull back on

the connector housing while pushing the connector in.

FIG. 1

S-Video DA Module & AF-10 Boards

General

Approvals CE, UL, cUL

Power Consumption (max.) – Module +9 VDC @ 500 mV

Power Connector – Module

2.1 mm DC power jack

Power – AF-10

100 - 240 VAC single phase, 50 - 60 Hz

Operational Temperature

32° - 110° F (0° - 43° C)

Humidity 0 to 90% non-condensing

Dimensions – Module 5.22 in. (13.26 cm) depth

5.82 in. (14.78 cm) width

1.42 in. (3.61 cm) height w/out feet

Weight – Module Approx. 1.5 lb. (0.68 kg)

Connector Options S-Video, Locking S-Video

S-Video Specifications

Frequency Response +/- 3 dB, 50 MHz or better

+/- 1 dB, 15 MHz or better

Signal to Noise Ratio (SNR)

Vin = 0.7 V, 100% IRE -45 dB

Level (max.)

Input:

Output:

+/- 1.75 V

+/- 1.75 V

Impedance

Input:

Output:

75 ohms

75 ohms

DC Offset Out (max.) Measured with 0 V on input +/- 20 mV

Video Bandwidth Specifications

Module FG1010-70

1:4 Board FG1040-452 5-out Board FG1040-455

+/-3 dB for 100 ft. (30.48 m) 10 MHz 10 MHz

+/-3 dB for 50 ft. (15.24 m) 150 MHz 100 MHz

+/-3 dB for 25 ft. (7.62 m) 200 MHz 125 MHz

+/-3 dB for 12 ft. (3.66 m) 100 MHz 50 MHz

+/-3 dB for 6 ft. (1.83 m) 100 MHz 50 MHz

+/-3 dB for 3 ft. (.91 m) 75 MHz 50 MHz

S-Video Module FG1010-70

1:4 S-Video AF-10 Board FG1040-452

5-out S-Video AF-10 Board FG1040-455

(Not to scale)

FIG. 2

Typical setup using S-Video DA Module

FIG. 3 Typical setup using S-Video DA boards in an AF-10

FIG. 4 Pull back on connector housing while pushing in

DVD

D

V

D

1:4 board

5-out board

Connector housing