Fujitsu MBC2036RC User Manual

Download Installation manual of Fujitsu MBC2036RC SERIES Storage for Free or View it Online on All-Guides.com.

Brand: Fujitsu

Category: Storage

Type: Installation manual

Model: Fujitsu MBC2036RC SERIES , Fujitsu MBC2073RC SERIES

Pages: 1 (0.07 Mb)

Download Fujitsu MBC2036RC SERIES Installation manual

Fujitsu MBC2036RC SERIES Installation manual - Page 1
1
MBC2073RC, MBC2036RC
HARD DISK DRIVES INSTALLATION GUIDE
CARE OF YOUR FUJITSU HARD DISK DRIVE (HDD)
Careful handling and installation of your HDD is paramount to the longevity of the unit. The internal mechanism of the HDD can be
seriously damaged if the HDD is subjected to forces outside the environmental specifications. When transporting the HDD, always use the
original packaging in which the HDD was delivered to you, and avoid exposing the HDD to extreme changes in temperature to minimize the
risk of condensation.
HANDLING
1. Never drop the unit. Handle it with care.
2. Never move the HDD while disks are spinning. Note that the disks spin when the HDD is powered on and also immediately after power
off. Refer to the Start/Stop specification for your HDD.
3. Never place the HDD in the vicinity of equipment giving off strong magnetic fields, such as CRT monitors, televisions, or loudspeakers.
4. Never use any cleaning agents or liquids on the HDD.
5. Always use an antistatic mat and wrist strap when handling the HDD. Hold the HDD by the base casting and never touch the components
on the printed circuit board assembly.
6. Never remove any labels from the HDD or deface them in any way.
7. Never open the HDD for any reason. Doing so will void any warranties.
8. Always pay close attention to the mounting specifications such as those for sway space and cooling. If the temperature difference
between the storage location and installation location exceeds 10°C, for temperature acclimation purposes, leave the HDD in the new
location for at least two hours before turning it on. This minimizes any risk of condensation forming on the HDD.
The HDD needs NO preventative or periodic maintenance during its service life if properly used in an appropriate environment.
INSTALLATION
1. ORIENTATION
The HDD can be installed flat on any of its six sides. Inclination from a vertical or horizontal plane should not exceed 5°.
2. MOUNTING SCREW INSTALLATION
Use all of 4 mounting screw holes on both sides of the HDD or the bottom. The inward projection of the screw from the HDD frame wall
at the corner must be 2.5 mm ±0.5 mm. Impact caused by the electric screwdriver must be within the HDD specifications.
3. COOLING
Allow space above and below the HDD to provide an adequate airflow. Fan cooling is recommended. The HDD temperature measured
on the cover surface (label side) should never exceed 60°C. See Table 1.
Table 1. Reference value of airflow
Environmental temperature Required velocity of airflow
35
°C > 0.2 m/s
40
°C > 0.6 m/s
45
°C > 1.1 m/s
50
°C > 1.8 m/s
4. BREATHING
Never cover the vent hole displayed on the label with the arrow.
5. CONNECTING
To avoid potential damage to the HDD, make sure that connector type and orientation is correct.
CAUTION: Your warranty may be voided if the connector is damaged as a result of incorrect insertion.
FUJITSU LIMITED
Storage Products Group
4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan
Copyright © 2007 FUJITSU LIMITED
http://www.fujitsu.com/
Undermentioned information is effective only in EU for traceability of the EMC Directive
Manufacturer :
Fujitsu Limited
4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan
Authorized representative importer / distributor in EU :
Fujitsu Europe Limited
Hayes Park Central, Hayes End Road, Hayes, Middlesex, UB4 8FE, United Kingdom
C141-E265-01EN