• Home
• Brands
• AMX Manuals
• AMX SPK-C-DT6.5
• Amx SPK-C-DT6.5 Install Manual

Amx SPK-C-DT6.5 Install Manual

Download Installation manual of AMX SPK-C-DT6.5 Speakers for Free or View it Online on All-Guides.com. This version of AMX SPK-C-DT6.5 Manual compatible with such list of devices, as: SPK-C-DT8-SWT, SPK-C6.5-SWT, SPK-EL6.5, SPK-EL6.5-SWT, SPK-EL8-SWT

1

2

Installation Guide

Matrix In-Ceiling Speakers

Overview

Matrix in-ceiling speakers provide exceptional acoustical performance using

superior components and crossover design. Matrix speaker enclosures

incorporate a floating bridge, which houses a unique pivoting tweeter assembly

that creates directionality for the user. FIG. 1 shows the three main types of

Matrix speakers (C Series, C-DT Series and EL Series):

Specifications:

C Series

C-DT Series

EL Series

Non-SWT Speakers

Each speaker has a Red (positive) terminal and a Black (negative) terminal.

Connect the appropriate wire from the keypad to Red and Black terminals

on the Left and Right speakers, as with any standard speaker installation.

SWT Speakers

Matrix Audio SWT Speakers are different from any other speaker available

on the market. They allow you to control a single zone of audio without a

keypad being installed. Therefore, some different wiring practices must be

considered for proper operation and control.

This is achieved by “daisy-chaining” from the first speaker to the second

speaker. The main run of 16/4 from the controller will go directly to the first

speaker in the zone. At the controller end, the wiring is left-to-right:

L D G R with the screws of the connector facing up.

At the speaker end, using the connector that is shipped with the speaker,

the wiring is: R G D L with the screws facing up, left-to-right. The labelling at

both ends must match or the IR control will not work (i.e.: if you used the

RED wire for the Left Audio labelled “L” at the zone output, you must use

the RED wire for the pin labelled “L” on the speaker connector).

Be sure to screw the connector down to the speaker crossover board

before installing and securing in the ceiling. This will ensure that the

connector will not disconnect after installation.

A single run of 16/2 must be run from the first speaker to the second

speaker.

SWT Speakers - Cutout Dimensions

The following table indicates the diameters of the circular cutout dimensions for

the 6.5” and 8” SWT Series Speakers:

Refer to the illustrations on the next page for detailed speaker dimensions

and wiring diagram.

FIG. 1 Matrix In-Ceiling Speakers

C Series Speakers

Models Available: • SPK-C6.5 (FG1130-01): 6.5" Speaker Pair, 125W

• SPK-C6.5-SWT (FG1130-02): 6.5" Speaker Pair with

Speaker Wire Technology, 125W

• SPK-C8 (FG1130-03): 8" Speaker Pair, 150W

• SPK-C8-SWT (FG1130-04): 8" Speaker Pair with Speaker

Wire Technology, 150W

Specifications: • Woofer: Constructed of mineral-filled anodized injection

molded polypropylene; diameter = C6.5s: 6.5", C8s: 8”

• Tweeter: Pivoting Silk Dome; diameter = 25mm

• Crossover: 24dB/Octave acoustical slopes

• Sensitivity (at 2.83v): C6.5s: 89dB, C8s: 90dB

• Frequency Response (+/-3dB): C6.5s: 50Hz - 20kHz,

C8s: 45Hz - 20kHz

• Nominal Impedance: 8 Ohms

• Recommended Power: C6.5s: 5 - 125W, C8s: 10 - 150W

• Weight: C6.5s: 4.0 lbs. (1.814 kg), C8s: 5.1 lbs. (2.313 kg)

• Drive Magnet: 15oz

C-DT Series Speakers

Models Available: • SPK-C-DT6.5 (FG1130-11): 6.5" Speaker (one), 100W

• SPK-C-DT6.5-SWT (FG1130-12): 6.5" Speaker (one) with

Speaker Wire Technology, 100W

• SPK-C-DT8 (FG1130-13): 8" Speaker (one), 100W

• SPK-C-DT8-SWT (FG1130-14):8" Speaker (one) with

Speaker Wire Technology, 100W

Specifications: • Woofer: Constructed of mineral-filled anodized injection

molded polypropylene; diameter = C-DT6.5s: 6.5",

C-DT8s: 8”

• Tweeter: Pivoting Silk Dome; diameter = 20mm (dual)

• Crossover: 24dB/Octave acoustical slopes

• Sensitivity (at 2.83v): C-DT6.5s: 89dB, C8s: 90dB

• Frequency Response (+/-3dB): C6.5s: 50Hz - 20kHz,

C-DT8s: 45Hz - 20kHz

• Nominal Impedance: 8 Ohms

• Recommended Power: C-DT6.5s: 5 - 100W,

C-DT8s: 10 - 100W

• Weight: C-DT6.5s: 4.05 lbs. (1.837 kg),

C-DT8s: 5.35 lbs. (2.427 kg)

• Drive Magnet: C-DT6.5s: 15oz, C-DT8s: 20oz

EL SeriesC Series C-DT Series

EL Series Speakers

Models Available: • SPK-EL6.5 (FG1130-21): 6.5" Speaker Pair, 80W

• SPK-EL6.5-SWT (FG1130-22): 6.5" Speaker Pair with

Speaker Wire Technology, 80W

• SPK-EL8 (FG1130-23): 8" Speaker Pair, 80W

• SPK-EL8-SWT (FG1130-24): 8" Speaker Pair with Speaker

Wire Technology, 80W

Specifications: • Woofer: Constructed of molded polypropylene; diameter =

EL6.5s: 6.5", EL8s: 8”

• Twe eter: Pivoting Silk Dome; diameter = 25mm

• Crossover: 24dB/Octave acoustical slopes

• Sensitivity (at 2.83v): 87dB

• Frequency Response (+/-3dB): EL6.5s: 60Hz - 20kHz,

EL8s: 50Hz - 20kHz

• Nominal Impedance: 8 Ohms

• Recommended Power: 5 - 80W

• Weight: EL6.5s: 4.0 lbs. (1.814 kg),

EL8s: 5.1 lbs. (2.313 kg)

• Drive Magnet: EL6.5s: 15oz, EL8s: 20oz

SWT Speakers - Cutout Dimensions (Diameters)

6.5” Speakers

• SPK-C6.5

• SPK-C-DT6.5

• SPK-EL6.5

7 1/4” (7.25”) / 18.415 cm

8” Speakers

• SPK-C8

• SPK-C-DT8

• SPK-EL8

8 5/8” (8.625”) / 21.907 cm