Gallien-Krueger 1001RB-II Owner's Manual

Download Owner's manual of Gallien-Krueger 1001RB-II Amplifier, Speakers for Free or View it Online on All-Guides.com. This version of Gallien-Krueger 1001RB-II Manual compatible with such list of devices, as: 1001RB/115, 1001RB/210, 700RB-II, 700RB/115, 700RB/210

Gallien-Krueger 1001RB-II Owner's manual - Page 1
1
Gallien-Krueger 1001RB-II Owner's manual - Page 2
2
Gallien-Krueger 1001RB-II Owner's manual - Page 3
3
Gallien-Krueger 1001RB-II Owner's manual - Page 4
4
Gallien-Krueger 1001RB-II Owner's manual - Page 5
5
Gallien-Krueger 1001RB-II Owner's manual - Page 6
6
Gallien-Krueger 1001RB-II Owner's manual - Page 7
7
Gallien-Krueger 1001RB-II Owner's manual - Page 8
8
Gallien-Krueger 1001RB-II Owner's manual - Page 9
9
Gallien-Krueger 1001RB-II Owner's manual - Page 10
10
Gallien-Krueger 1001RB-II Owner's manual - Page 11
11
Gallien-Krueger 1001RB-II Owner's manual - Page 12
12
Gallien-Krueger 1001RB-II Owner's manual - Page 13
13
Gallien-Krueger 1001RB-II Owner's manual - Page 14
14
Gallien-Krueger 1001RB-II Owner's manual - Page 15
15
Gallien-Krueger 1001RB-II Owner's manual - Page 16
16
6
700RB-II/1001RB-II Series
Quick Start
Quick Start
The 1001RB-II/700RB-II is designed to be simple to
operate. All controls have a well defined purpose and
are well behaved. These directions will take you
through the basics and give you a good start for
setting up your sound.
1. Plug it in:
Set the power switch to Off and connect the supplied
power cord, from the amplifier AC receptacle, to an AC
power outlet of proper voltage and power rating (see
safety information on page 5 for details).
2. Connect your cabinets:
Connect your speaker cabinets to the amplifier
outputs marked 700W/480W AMP ONLY or
SPEAKON OUTPUTS. Be sure not to exceed the
recommended speaker load below.
Maximum Recommended Speaker Loads:
One 4 Ohm, or two 8 Ohm cabinets on the Woofer
Amp. One or two 8 Ohm horns on the 50W/Tweeter
Amp.
If you are using an RBH Series cabinet, use the
supplied 4 conductor Speakon cable to connect to the
Speakon outputs on the rear panel of the amplifier.
In addition, set the switch on the RBH cabinet to Bi-
Amp.
For connection to all other cabinets, connect to the
1/4 outputs labeled 700W/480W amp only.
For more information on Bi-Amp and Normal mode,
see page 7.
Caution:
Do not connect any Speakon cables labeled Bridge
Mode to the 1001RB-II/700RB-II. These cables are
used for the old 2000RB amplifier only, and may
result in damage to your amplifier.
When using non-GK cabinets that haveWhen using non-GK cabinets that have
When using non-GK cabinets that haveWhen using non-GK cabinets that have
When using non-GK cabinets that have
Speakon connectors, only use a standard twoSpeakon connectors, only use a standard two
Speakon connectors, only use a standard twoSpeakon connectors, only use a standard two
Speakon connectors, only use a standard two
wire Speakon cable. The supplied fourwire Speakon cable. The supplied four
wire Speakon cable. The supplied fourwire Speakon cable. The supplied four
wire Speakon cable. The supplied four
conductor Speakon style connector couldconductor Speakon style connector could
conductor Speakon style connector couldconductor Speakon style connector could
conductor Speakon style connector could
result in damage to your amplifierresult in damage to your amplifier
result in damage to your amplifierresult in damage to your amplifier
result in damage to your amplifier
..
..
.
3. Initial front panel control settings:
Set all EQ controls and the Boost control to 12
oclock. The Voicing Filters should be turned all the
way down to get a flat response. Set the Level and
Master Volumes at 0. If you have a five string bass,
push the button marked String Bass in.
4. Plug in your bass:
Using an instrument cable, connect your bass to the
Input jack and press the power switch on. If you have
active tone controls on your bass, turn all of the
controls to the middle or flat position and turn the
volume all the way up. If you have conventional,
passive tone controls, turn all tone and volume
controls all the way up.
5. Level and Master Volume settings:
Set the Master Volume to 12 oclock. Turn the Input
volume up as you play. Try not to turn it past 1
oclock unless you want an overdrive effect. If the
yellow clip light turns on, press the -14db button in.
If it is still on, try turning the volume down on your
bass.
At this point:
You should be hearing your bass quite well. You can
use the Volume and Woofer-Master to achieve a
comfortable sound level.
Remember:Remember:
Remember:Remember:
Remember: If you need
more volume, turn up the Woofer-Master control first.