Radio Shack 20-Number Memory Speaker Phone Quick Manual

Download Manual  of Radio Shack 20-Number Memory Speaker Phone Telephone for Free or View it Online on All-Guides.com.

Radio Shack 20-Number Memory Speaker Phone Manual  - Page 1
1
Radio Shack 20-Number Memory Speaker Phone Manual  - Page 2
2
Connecting Your Phone
1.Plug one end of the supplied modular cord into the LINE jack
on the back of the phone.
2.Plug the other end into a modular phone line jack.
Notes:
Your telephone connects directly to a modular phone line
jack. If your phone line jack is not a modular jack, you can
update the wiring yourself using adapters and jacks from
your local RadioShack store. Or, call your telephone
company to update the wiring for you.
The USOC number of the jack to be installed is RJ11C.
Connecting the Handset
1.Plug one end of the supplied coiled cord into HANDSET on
the back of the base.
2.Plug the other end into the modular jack on the handset.
Setting the Dialing Mode
You may set your dialing mode to pulse or tone by selecting P or
T on the back of your base.
If you are not sure which service you have, do this simple test.
1.Set MODE to T.
2.Lift the handset or press SPEAKER and listen for the dial
tone.
3.Press any number other than 0.
If your dial tone stops, you have touch-tone service.
Leave MODE on T.
If the dial tone continues, you have pulse service. Set
MODE to P.
Note: TB is designated for use in the UK.
Using Tone Services on a Pulse Line
If you have a pulse line, you might need to use tone service for
special services, such as bank-by-phone. To use tone service,
do the following:
1.Be sure MODE is set to P and dial the number.
2.When the system answers, press
. Any addtional numbers
you press will send a tone signal.
After you hang up, your phone automatically resets to pulse dialing.
20-Number Memory Speaker Phone
43-3911
Your phone’s display is protected by a plastic label
during shipping. Peel off the label before using your
phone.
Installing Batteries
Insert 3 AAA batteries (not supplied). When appears or
the display becomes dim, replace the batteries.
When replacing batteries, be sure to put in new batteries
within one minute of removing the old ones. If not, your time
and date will be lost.
Use only fresh batteries of the required size and recommended type.
Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or
rechargeable batteries of different capacities.
Always remove old or weak batteries. Batteries can leak chemicals that may destroy electronic
parts.
Setting Up Your Phone
Preparing Your Phone
Battery
Compartment
MEM - Lets you store a number in
an indirect memory location (0-9).
See page 2.
M1 - M10 - lets you store 10
numbers and dial them with the
touch of a button.
REDIAL - lets you redial the last number
you dialed.
Mute - lets you talk to someone else
in the room without being overheard
by the person(s) on the phone.
Flash - lets you answer another
call if you have Call Waiting.
STORE - press to store numbers
in memory locations. See Memory
Dialing on page 2.
Opt/P - lets you select different
dialing options based on the
number you are calling.
Callback - lets you dial a phone
number in the Caller ID record
with the touch of a button.
Hold - lets you put a call on hold
while you do something else.
SPEAKER - press to switch between
the handset and speaker phone for
convenient hands-free use.
VOLUME - lets you control the
volume of the sound through your
handset and speaker phone.
Review - lets you scroll up
or down to set the desired
language, LCD contrast,
area code, and time/date
Also lets you scroll through
all numbers in your Caller
ID memory.
DELETE - lets you confirm your settings
during setup. Also lets you delete
records from your Caller ID memory.
3-Line LCD - lets you
review up to three lines of
information in your Caller
ID memory.
LINE
Jack
HANDSET
Jack
Ringer Volume - Hi/Low/Off
Set ringer’s volume to Hi or
Low as desired. Set to Off
for no sound.
MODE
P/T
Ringer R1/R2 - Set to
R1 for a high number of
rings or R2 for a lower
number of rings.
Battery Compartment
Plug your phone cord into
a modular phone line jack.
After you install your batteries, system information appears in the display, followed by E for English, F
for French and S for Spanish.
1.Repeatedly press REVIEW
e or d to select the desired language and press DELETE to store it. If
you do not select a language within a few seconds, the system defaults to English, the default
display language.
2.When LCD CONTRAST appears in the display, repeat step 1 to select one of the six settings.
3.When 000 SET AREA CODE displays and the 0 flashes, repeatedly press REVIEW
e or d until the
first digit of your area code appears. Press DELETE to store it. Repeat for each digit of your area
code.
Note: If you do not press a button, the system automatically sets the area code to 000.
4.Press REVIEW
e or d to set the hour, and press DELETE to store it.
Note: If you do not press a key, the system automatically sets the time to 12:00 PM 1/01.
5.Repeat Step 4 to store the minute, month and date.
To reset the language, contrast, area code and time/date settings:
1.Hold down DELETE and press d. LCD CONTRAST displays.
2.Repeat Step 1 above to reset each setting.
Choosing Your Settings
Index Card - Use the
supplied index card to
record the stored numbers.