RCA ANT1000R Manual

Download Limited warranty of RCA ANT1000R Antenna for Free or View it Online on All-Guides.com.

Brand: RCA

Category: Antenna

Type: Limited warranty for RCA ANT1000R

Pages: 1 (0.34 Mb)

Download RCA ANT1000R Limited warranty

RCA ANT1000R Limited warranty - Page 1
1
ANT1000
Flat Indoor Antenna
Middle section
Note about digital channels
To display digital signals on your TV, youll need to have the right
equipment: either a TV that is capable of decoding digital signals
or a digital converter box.
Troubleshooting
I have a cable ready TV. Why can’t I get channels above 13?
The tuners inside of cable ready TVs have two modes: one for cable
and one for antenna. When the TV is in cable mode, and you are
using an antenna, you will not be able to receive any channels above
13. Tox this, simply access the menu of your TV and switch the TV
from Cable/CATV mode to ANT/AIR mode.
I have my TV in a metal cabinet. Will the antenna work for me?
Any large metal objects will prevent the antenna signal from
reaching the antenna. You must place the antenna outside of or
above the metal cabinet.
My home has aluminum siding/insulation. Where should I place
my antenna?
Place the antenna near a window to minimize interference and
improve your reception.
Can I use my antenna in a basement?
TV signals usually cannot penetrate into basement locations due to
their lower elevation.
Please Note: Other variables, unrelated to antenna performance,
can effect your reception. These include distance from the
broadcasting source, and natural or man-made conditions (such as
buildings between the transmitting source and your antenna).
12 Month Limited Warranty
Audiovox Electronics Corporation (the Company) warrants to the original retail
purchaser of this product that should this product or any part thereof, under
normal use and conditions, be proven defective in material or workmanship within
12 months from the date of original purchase, such defect(s) will be repaired or
replaced (at the Companys option) without charge for parts and repair labor. To
obtain repair or replacement within the terms of this Warranty, the product along
with any accessories included in the original packaging is to be delivered with proof
of warranty coverage (e.g. dated bill of sale), specication of defect(s), transportation
prepaid, to the Company at the address shown below. Do not return this product
to the Retailer.
This Warranty is not transferable and does not cover product purchased, serviced
or used outside the United States or Canada. The Warranty does not extend to the
elimination of externally generated static or noise. This Warranty does not apply to
costs incurred for installation, removal or reinstallation of the product, or, if in the
Company’s opinion, the product has been damaged through acts of nature, alteration,
improper installation, mishandling, misuse, neglect, or accident. This Warranty does
not cover damage caused by an AC adapter not provided with the product.
THE EXTENT OF THE COMPANYS LIABILITY UNDER THIS WARRANTY
IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE
AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED TO DURATION OF THIS WARRANTY. ANY ACTION
FOR BREACH OF ANY WARRANTY HEREUNDER, INCLUDING ANY
IMPLIED WARRANTY, MUST BE BROUGHT WITHIN A PERIOD OF 24
MONTHS FROM THE DATE OF ORIGINAL PURCHASE. IN NO CASE
SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES WHATSOEVER. No person or representative is
authorized to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states/provinces do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damage so the above
limitations or exclusions may not apply to you. This Warranty gives you specic legal
rights and you may also have other rights which vary from state/province to state/
province.
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,
Hauppauge, NY 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, Unit 3,
Door 16, Mississauga, Ontario L5T 3A5
© 2008 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Trademark(s) Registered
www.rca.com
Printed in USA
ANT1000_IB_00
3. Flip the top of the middle
section over. Be careful to keep
the three screws in the holes!
Set the middle section top on
a flat surface, with the cable
extending toward you.
Assembly and Usage Instructions
7. Flip the entire assembly over and carefully tighten the screws.
DO NOT over tighten.
8. Connect the coaxial cable to your TVs antenna input.
Finding the best location for the antenna
Before you connect the antenna, determine the best spot in your
home for optimum reception. Visit www.antennaweb.org to see where
your local broadcasts are coming from. Then, try as much as possible
to avoid obstructions between these transmitters and your antenna.
IMPORTANT NOTES ABOUT ANTENNA PLACEMENT:
Although the ANT1000 may perform well when placed near or on
electronics such as TVs, these electronics may also interfere with
the antennas reception. If you experience reception difficulties
with the ANT1000, try moving it away from your TV or other
nearby electronic devices.
The ANT1000 works when on a at surface or stretched horizontally
on a wall or window. It will not work when stretched vertically on a
wall or window.
Note: Many times the best location for the antenna is close to or on a
window. You can use two-sided tape to mount to a window pane.
Assembling the ANT1000
IMPORTANT: Remove protective film from the antenna wing
sections before assembling the antenna.
1. Remove all parts from the box. The ANT1000 antenna package
includes the following items:
1 Middle Section 2 Antenna Wing Sections
(with coaxial cable) 3 Screws and Nuts
2. Unscrew the three screws holding the middle section together.
Remove the top of the middle section. Uncoil and extend the
coaxial cable built into this section.
4. Place the holes of one of
the wing sections over top
right and middle screws. The
letters AB printed on the
wing should be visible in the
upper left corner of the wing.
IMPORTANT: The antenna
wing must be installed in this
position first!
5. Place the holes of the second
wing over top of lower left
and middle screws. The wings
will slightly overlap. The AB
printed on the wing should
appear at the lower right
(upside down).
6. Place the bottom of the
middle section on the middle
section top. Make sure to line
up with the pegs at the top
and the holes with the screws.
3 Nuts