Revel Performa S30 User Manual

Download Operation & user’s manual of REVELL Performa S30 Racks & Stands, Speakers for Free or View it Online on All-Guides.com.

Brand: REVELL

Category: Racks & Stands , Speakers

Type: Operation & user’s manual for REVELL Performa S30

Pages: 6 (0.35 Mb)

Download REVELL Performa S30 Operation & user’s manual

REVELL Performa S30 Operation & user’s manual - Page 1
1
REVELL Performa S30 Operation & user’s manual - Page 2
2
REVELL Performa S30 Operation & user’s manual - Page 3
3
REVELL Performa S30 Operation & user’s manual - Page 4
4
REVELL Performa S30 Operation & user’s manual - Page 5
5
REVELL Performa S30 Operation & user’s manual - Page 6
6
Revel
®
Performa
S30 Mounting Kit
This mounting kit contains an integral
wall/ceiling mounting system for a pair of
Revel S30 loudspeakers. Three built-in
brackets (on the rear of the S30) are
designed for use with the supplied hardware
and will require installation into wallboard
between studs or rafters.
Tools included in this kit:
(6) hollow wall anchors with (6)
attached anchor screws
(2) ceiling safety bracket
(4) plastic E-Z anchors (for ceiling
installations)
(4) wood screws (ceiling installations)
installation template
Additional tools required for mounting
(not included):
tape measure
•adhesive tape
•pencil
power drill
•hammer
•carpenters level
stud finder
•utility knife
screw driver
Note:
The hollow wall anchors are only suitable for
installations on wall board (or ceiling) that is
between 1/2 and 5/8-inches thick. Deviation
from this thickness specification requires the
use of another suitable anchor.
WARNING
Harman Specialty Group assumes no
responsibility for proper installation of
hardware or for any personal injuries or
product damages resulting from improper
installation or a fallen loudspeaker.
CAUTION
Do not substitute mounting hardware! The
contents of this kit are part of a factory
tested mounting system that works on
wallboard only. To obtain additional
hardware, contact your authorized Revel
dealer.
To mount the S30 on a wall:
1. Determine wall locations for each pair
of left and right loudspeakers.
2. At each proposed site, use a stud
finder to locate the nearest studs,
which should be on 16-inch centers.
3. Tape the enclosed mounting template
to the wall between the studs, leaving
a minimum clearance of 3/4-inch
(19 mm) from the cabinet top to the
ceiling. Use a level to verify tilt is zero.
Be sure to account for any mouldings
when determining a minimum
clearance distance.
4. At each site, drill three 3/8-inch holes
(9.5 mm) at the designated locations
on the mounting template.
5. With utility knife, create a cutout for
speaker wire within the noted bound-
ary.
6. If the anchor has a washer, remove
and discard it.
7. At each site, hammer the anchor into
the wall with the screw in place.
8. Tighten each screw clockwise until the
anchor cinches down and the screw
will no longer turn.
9. With the screw driver, carefully back
out the screw 3/16-inch (5 mm) in
order to leave room for the brackets on
the speaker cabinet.
10. At each site, route the speaker wire
through the cutout and using correct
polarity, attach the ends to the termi-
nals on the rear of the loudspeakers.
11. Align the brackets on each cabinet
with the screws on the wall, as shown
in Figure 2 (next page). Slide each
cabinet securely down onto the screws.
12. Remove the tape and template.
Note:
For best performance, mount the S30s at least
18-inches (46 cm) away from the ceiling at an
optimum height of 15 degrees above the
prime listening position. See the Revel S30
Loudspeaker Owner’s Manual for placement
instructions.