• Home
• Brands
• GE Manuals
• GE 500A436P006
• GE 500A436P006 Installation Instructions Manual

GE 500A436P006 Installation Instructions Manual

Download Installation instructions manual of GE 500A436P006 Dryer, Power Supply for Free or View it Online on All-Guides.com. This version of GE 500A436P006 Manual compatible with such list of devices, as: DLSR483GG7WW, DLSR483GG8WW, DSLVR48GH5WW, GTDL200GM2WW, NVLR223GGWW - 5.8 cu. Ft. Gas Dryer

1

2

3

4

5

6

7

8

nstal ati

nst cti

G

If you have any questions, call 1-800-GECARES (US) or 1-800-361-3400 (Canada)

or Visit our Web site at: www. GEAppliances.com

BEFOREYOU BEGIN

Read these instructions completely and

carefully.

"IMPORT. NT-Save hese

instructions for local inspector's use.

"IMPORTANT-obse,,,e

all governingcodes and ordinances.

* Note to Installer- Be sure to leave

these instructions with the customer.

* Note to Customer - Keep these

instrucOons with your Use and Care

Book for fhture reference.

* Before the old dwer is removed f_om

smwice or discarded, remove the dwer

door.

* Inspect the dwer exhaust outlet and

straighten the outlet walls if they are

bent.

* Seiwice information and the wiring dia-

gram are located in the control console.

* Do not allow children on or in the

appliance. Close supexMsion of child-

ten is necessa W when the appliance is

used near children.

* Install the dwer where the temp-

erature is above 50°F for satisf_mtory

operation of the dwer control system.

TOOLS YOU

WiLL NEED

(x2)

10"ADJUSTABLEWRENCHES

8"PIPEWRENCH LEVEL

SLIPJOINTPLIERS FLATBLADESCREWDRIVER

WARN NG RIsKoF

* To reduce the risk of severe i_j ury or death, follow all installation instructions.

* Clothes dryer installation must be performed by a qualified installer.

* Install the clothes dwer according to these instructions and in accordance with

local codes. In the absence of local codes, installation Illust comply with National

Fuel (;as Code, ANSIZ223.1/NFPA 54 or the Canadian Natural (;as and Propane

Installation Code, CSA B 149.1.

* (,Mifornia Sidle DiJnking 14.'_terand Toxic En_)±wementAct

This act requires the go, ernor of CaliR)rnia to publish a list of substances known to the

state to cause cancer, birth def>cts or other reproductixe harm and requires businesses to

warn customers of potential exposure to such substances. Gas appliances can cause minor

exposure to four of these substances, namel)benzene, carbon monoxide, formaldehyde

and soot, caused primaril) b) the incomplete combustion of natural gas or [,P fi_els.

Properl) adjusted dQers will minimize incomplete combustion. Exposure to these

substances can be minimized fllrther b) properly xenting the dQ'er to the outdoors.

* This (hTer must be exhausted to the outdoors.

* Use only 4" rigid metal ducting fbr exhausting the clothes (hTer to the outdoors.

* DO NOT install a clothes (hTer with flexible plastic ducting materials. If flexible

metal (semi-rigid or foil-D,pe ) duct is installed, it must be UL-listed and installed

in accordance with the instructions fbt]nd in "Connecting Tile Dryer To House

Vent" on page 6 of this manual. Flexible ducting materials are known to collapse,

be easily crushed, and trap lint. These conditions will obstruct dwer airflow and

increase the risk of fire.

* Do not install or store this appliance in any location where it could be exposed to

water and or weather.

* Save these instructions. (Installers: Be sure to leave these instructions with the

customer).

in the state of Massachusetts, installation must be performed by a qualified

or licensed contractor, plumber, or gasfitter qualified or licensed by the state.

MATERIALS YOU WiLL NEED

4"DIA.METALDUCT e===_

(RECOMMENDED)

4"DIAMMETALELBOW

4"DIA.FLEXIBLEMETALSEMI-RIGID)

ULLSTEDTRANST ONDUCT

(IFNEEDED)

KITWXO8X10077(INCLUDES2 ELBOWS)

4"DIA.FLEXIBLEMETAL(FOILTYPE)

ULLISTEDTRANSITIONDUCT

(IFNEEDED.)

(x2)

PIPE 0

EXHAUSTHOOD COMPOUNDSOAPSOLUTION

FORLEAKDETECTION

4"DUCTCLAMPS

OR

4"SPRINGCLAMPS _ _

Q_(x2) FLEXIBLEGASLINECONNECTORGLOVES

DUCTTAPE

SAFETYGLASSES

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Verify,Your Gas Installation (see section 2).

Prepare the Area and Exhaust for Installation of

New Dwer (see secdon 1).

Check and Insure the Existing External Exhaust is

Clean (see secdon 1) and Meets Attached Installation

Specifications (see secdon 6).

Remove the Foam Shipping Pads (see section 1).

Move the D_Ter to the Desired Location.

Level Your Dryer (see section 8).

Connect the (;as Supply (see section 3) and check

for leaks (see section 4).

Step 8

Step 9

Step 10

Step 11

Connect the External Exhaust (see secdon 7).

Connect the Power Supply (see section 5).

Check the Operation of the Power Supply, Gas

Connections, and Venting.

Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation see section 9.

For Bathroom or Bedroom Installation see section 10.

For Mobile or Manufhctured Home see section 11.