• Home
• Brands
• GE Manuals
• GE DBSR453EBWW
• GE DBSR453EBWW Installation Instructions Manual

GE DBSR453EBWW Installation Instructions Manual

Download Installation instructions manual of GE DBSR453EBWW Dryer for Free or View it Online on All-Guides.com. This version of GE DBSR453EBWW Manual compatible with such list of devices, as: DBSR453EBWW, DRSR483EDWW, DWSR405EBWW, DWSR483E - Appliances 7.0 cu. Ft. Electric Dryer, DWSR483EBWW

1

2

3

4

5

6

7

8

Installation

Instructions

Electric Dryer

37

BEFORE YOU BEGIN

TOOLS YOU

WILL NEED

MATERIALS YOU WILL NEED

FOR YOUR SAFETY:

WARNING

Read these instructions completely and carefully.

PHILLIPS SCREWDRIVER

SLIP JOINT PLIERS

LEVEL

GLOVES

SAFETY GLASSES

DRYER POWER

CORD KIT

(NOT PROVIDED

WITH DRYER)

UL RATED 120/240V, 30A

WITH 3 OR 4 PRONGS.

IDENTIFY THE PLUG TYPE

AS PER THE HOUSE

RECEPTACLE BEFORE

PURCHASING LINE CORD.

4" DUCT

CLAMPS (2)

OR

4" SPRING

CLAMPS (2)

EXHAUST HOOD

3/4" STRAIN RELIEF

UL RECOGNIZED

• Use only rigid metal or flexible metal 4-in. diameter

ductwork for exhausting to the outdoors. Never

use plastic or other combustible, easy-to-puncture ductwork.

• This appliance must be properly grounded and installed

as described in these instructions.

• Do not install or store appliance in an area where it

will be exposed to water and/or weather

• Install the dryer where the temperature is above 50ºF

for satisfactory operation of the dryer control system.

4" DIA. METAL

ELBOW

• IMPORTANT - Save these

instructions for local inspector’s use.

•

IMPORTANT - Observe all

governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions with

the customer.

• Note to Customer - Keep these instructions with your Use

and Care Book for future reference.

• Exhausting the dryer to the outdoors is strongly recom-

mended to prevent large amounts of moisture from being

blown into the room.

• Before the old dryer is removed from service or discarded,

remove the dryer door.

• Service information and the wiring diagram are located in

the control console.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the appliance is

used near children.

NOTE: Installation and service of this dryer

requires basic mechanical and electrical skills.

It is your responsibility to contact a qualified

installer to make the electrical connections.

Step 1 Prepare the Area and Exhaust for Installation of

New Dryer (see section 1).

Step 2 Check and Ensure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Specifications (see section 3).

Step 3 Remove the Foam Shipping Pads (see section 1).

Step 4 Move the Dryer to the Desired Location.

Step 5 Connect the Power Supply (see section 2).

Step 6 Connect the External Exhaust (see section 4).

Step 7 Level Your Dryer (see section 5).

Step 8 Check the Operation of the Power Supply

and Venting.

Step 9 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation, see section 6.

For Bathroom or Bedroom Installation, see section 7.

For Mobile or Manufactured Home see, section 8.

For side or bottom exhaust, see section 9.

Questions on Installation? Call: 1-800-GECARES (US)

or Visit our Web site at:

www.GEAppliances.com (US)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL DUCT

(IF NEEDED)

FLAT BLADE SCREWDRIVER

DUCT TAPE