GE GTDX185ED2CC Installation Instructions Manual

Download Installation instructions manual of GE GHDN520ED2WS Dryer for Free or View it Online on All-Guides.com. This version of GE GHDN520ED2WS Manual compatible with such list of devices, as: GLDS560ED2WW, GTDP180ED2WW, GTDP200EF0WS, GTDX185ED2CC, GTDX400ED2WS

GE GHDN520ED2WS Installation instructions manual - Page 1
1
GE GHDN520ED2WS Installation instructions manual - Page 2
2
GE GHDN520ED2WS Installation instructions manual - Page 3
3
GE GHDN520ED2WS Installation instructions manual - Page 4
4
GE GHDN520ED2WS Installation instructions manual - Page 5
5
GE GHDN520ED2WS Installation instructions manual - Page 6
6
GE GHDN520ED2WS Installation instructions manual - Page 7
7
GE GHDN520ED2WS Installation instructions manual - Page 8
8
Installation
instructions
Electric Dryer
02
Questions? Call 800.GE.CARES {800.432.2737) or visit our Web site at: GEAppliances.com
In Canada, cell 1.800.561.3344 or visit www.GEAppliances.ca
BEFORE YOU BEGIN
Readtheseinstructionscompletelyandcarefully.
IMPORTANT- save these instructions for local
inspector's use.
IMPORTANT- Observe all governing codes and
ordinances.
Noteto Installer - Besureto leavetheseinstructionswith the
customer.
Noteto Customer- Keeptheseinstructionswithyour Owner's
Manualfor future reference.
Before the old dryer is removed from service or discarded,
removethe dryer door.
Inspect the dryer exhaust outlet and straighten the outlet
walls if they are bent.
Serviceinformation andthe wiring diagram are locatedin the
controlconsole.
Donot allow childrenon or in the appliance.Closesupervision
of children is necessary when the appliance is used near
children.
tnstall the dryer where the temperature is above 50°F for
satisfactoryoperation of the dryer control system.
Product failure due to improper installation is not
covered under the warranty.
WARNING RISK OF FIRE
, To reduce the risk of severe injury or death, follow all
installation instructions.
, Clothes dryer installation must be performed by a
qualified installer.
, Install the clothes dryer according to these instructions
and in accordance with local codes.
, This dryer must be exhausted to the outdoors.
, Use only 4" rigid metal ducting for exhausting the
clothes dryer to the outdoors.
, DO NOT install a clothes dryerwith flexible plastic ducting
materials. If flexible metal (semi-rigid or foil-type) duct is
installed, it must be UL listed and installed in accordance
with the instructions found in Connecting The Dryer To
House Vent on page 5 of this manual. Flexible venting
materials are known to collapse, be easily crushed, and
trap lint. These conditions will obstruct dryer airflow and
increase the risk of fire.
, Do not install or store this appliance in any location
where it could be exposed to water and or weather.
, Save these instructions. (Installers: Be sure to leave
these instructions with the customer).
, Install the clothes dryer according to the manufacturer's
instructions and local codes.
NOTE: Installation and service of this dryer
requires basic mechanical and electrical
skills. It is your responsibility to contact a
qualified installer to make the electrical
connections.
TOOLS YOU WILL NEED
SLIPJOINTPLIERS PHILLIPSSCREWDRIVER
FLATBLADESCREWDRIVER
TOOLS YOU WILL NEED
)
4IIDIAMETALDUCT _/II
(RECOMMENDED)
#'DUCT 4"DIAMETAL
CLAMPS(2) ELBOW
OR
#'SPRING
CLAMPS(2)
DUCTTAPE
4"DIAFLEXIBLEMETAL(SEMFRIGID)
ULLISTEDTRANSITIONDUCT
(IFNEEDED(
KITWXRBX1RR77(INCLUDES2ELBOWS)
4I1DIAFLEXIBLEMETAL(FOILTYPE)
ULLISTEDTRANSITIONDUCT(IFNEEDED)
EXHAUST SAFETY
HOOD GLASSES
GLOVES
3/4"STRAIN
RELIEF
ULRECOGNIZED
DRYERPOWER
CORDKIT
(NOTPROVIDED
WITHDRYER)
ULRATED
12R/240V,3RA
WITH3OR4 PRONGS
IDENTIFYTHEPLUG
TYPEASPERTHE
HOUSERECEPTACLE
BEFOREPURCHASING
LINECORD
Step 1 Prepare the Area and Exhaust for Installation of
New Dryer (see section 1).
Step 2 Check and Ensure the Existing External Exhaust
is Clean (see section 1)and Meets Attached Installation
Specifications (see section 3).
Step 3 Remove the Foam Shipping Pads (see section 1).
Step 4 Move the Dryer to the Desired Location.
Step 5 Connect the Power Supply (see section 2).
Step 6 Connect the External Exhaust (see section 4).
Step 7 Level Your Dryer (see section 5).
Step 8 Check the Operation of the Power Supply & Venting.
Step 9 Place the Owner's Manual and the Installation
Instructions in a location where they will be noticed by the
owner.
For Alcove or Closet Installation, see section 6.
For Bathroom or Bedroom Installation, see section 7.
For Mobile or Manufactured Home see, section 8.
Forgarage installation (ifallowed by local codes),see section9.
For side or bottom exhaust, see section 10.
234D2004PO02 31-16308 O3-./.3 GE