RUSSOUND DAN Instruction Manual

Download Instruction manual of Russound DAN Other for Free or View it Online on All-Guides.com.

Brand: Russound

Category: Other

Type: Instruction manual

Model: Russound DAN , Russound DSC

Pages: 2 (0.16 Mb)

Download Russound DAN Instruction manual

Russound DAN Instruction manual - Page 1
1
Russound DAN Instruction manual - Page 2
2
LIMITED WARRANTY
The Russound DAN and DSC are both fully guaranteed for Two (2) years from the date of purchase
against all defects in materials and workmanship. During this period, Russound will replace any defec-
tive parts and correct any defect in workmanship without charge for either parts or labor. For this war-
ranty to apply, the unit must be installed and used according to its written instructions. If service is nec-
essary, it must be performed by Russound. The unit must be returned to Russound at the owner’s
expense and with prior written permission. Accidental damage and shipping damage are not considered
defects under the terms of the warranty. Russound assumes no responsibility for defects resulting from
abuse or servicing performed by an agency or person not specifically authorized in writing by
Russound. Damage to or destruction of components due to improper use voids the warranty. In these
cases, the repair will be made at the owner’s expense. To return for repairs, the unit must be shipped to
Russound at the owner’s expense, along with a note explaining the nature of the service required. Be
sure to pack in a corrugated container with at least 3 inches of resilient material to protect the unit
from damage in transit.
5 Forbes Rd. Newmarket, NH 03857, USA
603.659.5170 • Fax 603.659.5388
Come visit us at:
CLEAR PROCEDURE INSTRUCTIONS
To Clear Individual Commands:
1) Press the Clear button. The Program Indicator will be illuminated. CAU-
TION: Do not press the Clear button for more than 1 second. Holding the
Clear button for more than 1 second will cause all stored commands to
be deleted.
2) Select the layer in which the command resides by selecting the source
input on the main keypad.
3) Press the command key to be cleared.
4) To continue to delete commands, repeat steps 2 and 3.
5) To exit the Clear mode, press the Clear button twice or wait 5 seconds for
the DSC or DAN to exit the Clear mode automatically.
To Clear All Commands:
1) Press and hold the Clear button for more than 1 second.
2) The Program, Stored and Error indicators will all light in sequence.
3) All commands previously stored in the DSC or DAN Keypad are now
deleted.
4) The DSC or DAN Keypad is now ready to be re-programmed (see
Programming instructions).
Reset Procedure Instructions:
The Reset button is used to restart the DSC or DAN Keypad if any problem
occurs during programming. If the DSC or DAN Keypad locks up for any rea-
son, follow the procedure below.
1) Press the Reset button (shown in Figure 2).
2) The Program indicator will illuminate momentarily.
3) The DSC or DAN Keypad will now operate properly. No stored information
will be lost.
OPERATION INSTRUCTIONS
1) Read the Control Features section of the Multi-Zone Controller manual.
2) Select the source that you wish to control on the main keypad (this will
also select the source for listening).
3) Press the command key(s) on the DSC or DAN which have been pro-
grammed with the commands that you wish to execute.
4) The Program indicator will flash as the command is outputted. If the
Program indicator does not flash when the command key is pressed, the
command was not stored properly.
Direct Source
Control Keypads
DSC
AND
DAN
Instruction Manual
Russound
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
Conforms to
UL 6500
Certified to
CAN/CSA
E65-94
DSC & DAN
DIRECT ACCESS
NUMERIC SOURCE KEYPAD
897
564
2
31
0
ENTER
DIRECT SOURCE CONTROL
SEEK
MODE
SELECT
SCAN
REV2
040502
DAN & DSC manual 4/16/02 9:22 AM Page 1