Panasonic AW-EX500N User Manual

Download Operating instructions manual of Panasonic AWEX500N - SIGNAL CONVERTER Accessory for Free or View it Online on All-Guides.com.

Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 1
1
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 2
2
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 3
3
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 4
4
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 5
5
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 6
6
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 7
7
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 8
8
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 9
9
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 10
10
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 11
11
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 12
12
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 13
13
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 14
14
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 15
15
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 16
16
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 17
17
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 18
18
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 19
19
Panasonic AWEX500N - SIGNAL CONVERTER Operating instructions manual - Page 20
20
• When two optional cards are to be used in combination
with the AW-EX100, remember that an AW-PB3** card
and an AW-PB5** card cannot be used at the same time.
Instead, use two PB3** cards or two PB5** cards.
• The approximate input/output time differences of the
AW-EX500 are as shown below.
- 5 -
• The AW-EX500 generates various sync signals internally
on the basis of the signals which are supplied to it. For this
reason, it cannot output normal signals if no signals are
supplied. To use this signal converter, therefore, signals
must be supplied to it.
• The AW-EX500 does not come with a cable compensation
circuit for the input signals. If the cable from the signal
source is too long, use a cable compensator immediately
in front of the AW-EX500 input.
• When signals with significantly high jitter such as from a
VTR are used as the signal source, the output signals may
be disrupted. Particularly when an SDI card is used, the
jitter performance may not satisfy the standard. In a case
like this, shape the sync signals using a TBC (time base
corrector) or other such device at a stage prior to the
AW-EX500 input.
• For further details on the settings and connections of an
optional card, refer to the operating instructions
accompanying the optional card concerned.
• If the AW-PB302 card is used, it will not be possible to use
the composite video signals from the card’s D-sub
connector: therefore, leave the connector unconnected.
Neither can Y/C signals be selected.
Analog composite input
AW-EX500 1H +
analog output approx. 7.6µsec
Analog composite input
AW-PB302 1H +
output approx. 5.6µsec
Analog component input
AW-EX500 1H +
analog output approx. 7.6µsec
Analog component input
AW-PB302
Approx. 0.4µsec
output
SDI signal input*
AW-EX500
Approx. 3.6µsec
analog output
SDI signal input*
AW-PB302
Approx. 2.3µsec
output
*Signal source: AW-E650 + AW-PB504, time difference from
AW-E650 video output