GE WCCB1030D1WC Installation Instructions Manual

Download Installation instructions manual of GE WCCB1030D1KC Warranty Washer for Free or View it Online on All-Guides.com. This version of GE WCCB1030D1KC Warranty Manual compatible with such list of devices, as: WCCB1030D1KC Warranty, WCCB1030F2WC Warranty, WCCD2050D1WC Warranty, WCCD2050F2WC Warranty, WCRD2050D1WC Warranty

GE WCCB1030D1KC Warranty Installation instructions manual - Page 1
1
GE WCCB1030D1KC Warranty Installation instructions manual - Page 2
2
GE WCCB1030D1KC Warranty Installation instructions manual - Page 3
3
GE WCCB1030D1KC Warranty Installation instructions manual - Page 4
4
GE WCCB1030D1KC Warranty Installation instructions manual - Page 5
5
GE WCCB1030D1KC Warranty Installation instructions manual - Page 6
6
GE WCCB1030D1KC Warranty Installation instructions manual - Page 7
7
GE WCCB1030D1KC Warranty Installation instructions manual - Page 8
8
GE WCCB1030D1KC Warranty Installation instructions manual - Page 9
9
GE WCCB1030D1KC Warranty Installation instructions manual - Page 10
10
GE WCCB1030D1KC Warranty Installation instructions manual - Page 11
11
GE WCCB1030D1KC Warranty Installation instructions manual - Page 12
12
INSTALLATION REQUIREMENTS
LOCATION
Washer must be installed on firm
flooring to minhnize vibration during
spin cycles, Concrete flooring is best,
but wood base is sufllcient providing
floor support meets FHA standards.
Washer should not be installed on rugs
or exposed to the weather.
PLUMBING
WATER PRESSURE - Must be 10 psi
minimum to 150 psi maximum
dynamic pressure measured at faucet.
WATER TEMPERATURE - House-
hold water heater should be set to
deliver water at i20 ° to 150°F (50 ° to
66_'C) IN THE WASHER when HOT
wash is selcctcd.
SHUT-OFF VALVES - Both hot and
cold shut-off valves (faucets) should be
supplied.
. DRAIN - Water may be drained into
a standpipe or set tub The discharge
height MUST NOT BE LESS THAN 30
INCHES nor more than g t:eet above
the base of the washer, The standpipe
must be 1-1/2 inches minimum inside
diameter and must be open to the
atmosphere,
ELECTRICAL
This appliance must be supplied with
i 15V, 60 Hz, and connected to an
individual, properly grounded branch
circuit, protected by a 15 or 20 amp
circuit breaker or thne-delay fuse,
TOOLS YOU W|LL NEED
Socket set
Slip,joint pliers
TYPICAL HOSE INSTALLATIONS
i
I I 1 I I tlitl D NHOSEC"RE
DRAIN HOSE
RECESSEDPLUMBING
TAPE TO
FILLHOSE
DRAIN HOSE
Drain hoses must be securely
attached to washer and drain facility
with plastic tie strap or tape,
Fil! hose connections must be tight.
STEP 1
PREPAREWASHER FORINSTALLATION
1. Remove cardboard inner pack and
installation accessolics from under
Iid, Drain hose is in washer basket.
2. Grasp retainer rod on lower right
side (has a tag on strap), and pull
rod straight out and discard.
RIGHT
SiDE OF
WASHER
REMOVE
S]{IPPIN6
RETAINER
3. Move washer to instaItation location
for remaining hose and electrical
preparation.
BOTI'OM OF
LEVELI SHER
LEGS /
Specifications subiect to change
without notice.
Pub. No. 31-15400 Dwg. 143B9310P026